49 Chevy 1/2 Ton Parting Out
5 Attachment(s)
I have decided to crush out my older trucks to make room for more later model parts. With the advent of reproduction and China influx it is time to let them go. I will keep this truck around for a week or so . For now I have the following parts.
Wiper Linkage $35 Seat Skirts $35 Cowl vent $35 Hood Hinges $40 Set Inside Window Frames $50 Pair Column Drop Clamp $20 Pitman Arm $35 Road Draft Tube $35 Valve Cover $25 Throttle Linkage $40 Foot Stomp Starter Linkage $40 Front Bumper Brackets $50 Side Cowl Vent $35 Glove Box Hinges $20 Radio Speaker Cover With Trim $40 Igintion Switch With Key $25 Other Parts All parts plus shipping. Paypal or USPS Postal M.O. . Fast shipping with USPS Priority or Fed X ground on the bigger items. Thanks |
Re: 49 Chevy 1/2 Ton Parting Out
Is the wiper linkage complete?
Thanks |
Re: 49 Chevy 1/2 Ton Parting Out
I will make it complete . Set of under dash wiper linkage , bezel and outside arms. Should buy the little rubber gaskets that go on the cowl. Also will need the new wiper blades as these are poor. Thanks
|
Re: 49 Chevy 1/2 Ton Parting Out
Cool.How much shipped to 90604?
Thanks |
Re: 49 Chevy 1/2 Ton Parting Out
I will not know till I get it packaged and your zip. Send me your zip and I will get a quote.
|
Re: 49 Chevy 1/2 Ton Parting Out
My zip is 90604.
Thanks. |
Re: 49 Chevy 1/2 Ton Parting Out
Shipping via Prority Mail is $14.
|
Re: 49 Chevy 1/2 Ton Parting Out
Would you take $45 shipped?
|
Re: 49 Chevy 1/2 Ton Parting Out
No
|
Re: 49 Chevy 1/2 Ton Parting Out
Ok,no problem.
$49 total right? I can do paypal. |
Re: 49 Chevy 1/2 Ton Parting Out
Ok , Pm sent with paypal information
|
Re: 49 Chevy 1/2 Ton Parting Out
Linkage shipped via USPS Priority Mail. Tracking # sent . Thanks again.
|
Re: 49 Chevy 1/2 Ton Parting Out
Cool,thanks.
|
Re: 49 Chevy 1/2 Ton Parting Out
How much you want for the 2 gauges?
|
Re: 49 Chevy 1/2 Ton Parting Out
$75 for the pair. The speedometer works but will need a needle and face kit. I tested the temp gauge on the cluster and it works , other gauges untested but look good. Would be a good set to restore.
|
Re: 49 Chevy 1/2 Ton Parting Out
I'll pass. Thank for getting back to me.
|
Re: 49 Chevy 1/2 Ton Parting Out
5 Attachment(s)
Added Gauge Cluster $40 And Speedometer Temp gauge tested and works. Will need to have a face decal kit and bezel . The speedometer and odometer both work. Will need a decal kit and needle (farmer brown added a tootpic) . $40 .
|
Re: 49 Chevy 1/2 Ton Parting Out
How much for the parking brake handle, mount and rod assembly that connect to the floor? 14304
|
Re: 49 Chevy 1/2 Ton Parting Out
The park brake setup sold locally . Did you just need the pull rod under the dash or a complete setup? Thanks
|
Re: 49 Chevy 1/2 Ton Parting Out
Just need the pull rod.
|
Re: 49 Chevy 1/2 Ton Parting Out
5 Attachment(s)
I usually sell them with the complete e-brake setup but have this lone one that I was starting to build another set. Would need light straightening . There are two little cracks (one on each side see photo) on the angle bracket. Good stud.$25
|
Re: 49 Chevy 1/2 Ton Parting Out
Thanks for looking in to this. I have the bracket on my truck still. Was thinking of just threading a rod if I could. Probably just as easy at this point.
|
Re: 49 Chevy 1/2 Ton Parting Out
How much for cut out cowl section on drivers side where vent goes, (with 4" or so material on outsides to work with)with a vent door, etc. Want to install one on my 51. Need everything for complete functioning install. 27587 zip code.
|
Re: 49 Chevy 1/2 Ton Parting Out
2 Attachment(s)
Hi Josh , I have the one pictured from a different truck for $50 . I do not think it has enough suround for what you are trying to do as you will need the complete pivot holder and inner kickpanel That is what I normally sell the door for by itself. I can cut the one out the truck pictured but it may be on Friday. Price will be more depending if on how much I take. I recommend also getting the inside cowl panel also as there are at least two different styles of this so recommend a matched set. Will try to get the other one cut out either on Friday or Saturday. Thanks Paul
|
Re: 49 Chevy 1/2 Ton Parting Out
Thanks man, Im going to try to find one complete a little nicer before I commit, Thanks again.
|
All times are GMT -4. The time now is 07:46 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com