accelerator rod to edelbrock carb ?
 

How do you hook up the accelerator rod to the edelbrock carb? Do I have to instal the bracket from the other carb? Does anyone have any pix

I drilled out the hole on the carb, no problem since
I might have a pic somewhere.

------------------
'69 G.M.C. 350/350. Trying to clean up the left over damage from the Dope-Smokin-Old-Man
I've been dubbed the Longhorn Freak/Fanatic/Expert, I just hope I can live up to it.
FINALLY got the HORNIAC...a '70 one ton Longhorn with a Pontiac 350/350 and lots of 'personality'. Check out The Longhorn Webite.
If you need a pic posted, E-mail me at longhornmail@yahoo.com
Andy, in Columbus Ohio

Yup, here it is...
http://www.freephoto-i.net/users/longhorn/throttle2.jpg

------------------
'69 G.M.C. 350/350. Trying to clean up the left over damage from the Dope-Smokin-Old-Man
I've been dubbed the Longhorn Freak/Fanatic/Expert, I just hope I can live up to it.
FINALLY got the HORNIAC...a '70 one ton Longhorn with a Pontiac 350/350 and lots of 'personality'. Check out The Longhorn Webite.
If you need a pic posted, E-mail me at longhornmail@yahoo.com
Andy, in Columbus Ohio

I used a linkage connector from holley..its aboout 5/8" round with a threaded hole and a tappered shaft to fit in the carb..the tappered part has a hole though it for a cotter pin...I think it was about 10 bucks

Thanks you guys for your help. I gess I panic for nothing. I posed this question an got 3 responces and a picture in less than a 1/2 hour, isint this site grate?

Hey longhorn...you got a pic with a detent cable hooked up..trying to figure the best throttle spring placement

detent cable?

------------------
'69 G.M.C. 350/350. Trying to clean up the left over damage from the Dope-Smokin-Old-Man
I've been dubbed the Longhorn Freak/Fanatic/Expert, I just hope I can live up to it.
FINALLY got the HORNIAC...a '70 one ton Longhorn with a Pontiac 350/350 and lots of 'personality'. Check out The Longhorn Webite.
If you need a pic posted, E-mail me at longhornmail@yahoo.com
Andy, in Columbus Ohio

wait...a kickdown cable, or a '71/'72 cable throttle...either way, i don't have a pic. The kickdown should be where my throttle return spring is hooked,a nd oneday, it will be.

------------------
'69 G.M.C. 350/350. Trying to clean up the left over damage from the Dope-Smokin-Old-Man
I've been dubbed the Longhorn Freak/Fanatic/Expert, I just hope I can live up to it.
FINALLY got the HORNIAC...a '70 one ton Longhorn with a Pontiac 350/350 and lots of 'personality'. Check out The Longhorn Webite.
If you need a pic posted, E-mail me at longhornmail@yahoo.com
Andy, in Columbus Ohio

This help ya Bigjim. The stud the tv cable hooks to is sold seprately by Edlebrock.
[img]http://communities.msn.com/_Secure/0MgAAAEUQXo1N5bSbIdaPdzGuJ9aA!*JS1hpUnjzE4i8mtXedWXEZjD3qKcgCnmOrF!7pwyMA1D6zS0sss386Zg/tv-linkage.JPG[/img]

------------------

• 71 Chevy CST Long Fleet 350/350/3.07 leaf rear.
• Email: 67-72truckparts@nanosecond.com

Yup that helps....Ive got mine almost like that...cant believe I didnt use the intake manifold bolt to hold the spring holder thingy..I used the thermostat housing bolt. I spent a weekend trying to put the spring in the rear...with no luck..Thanks

It does look better to the rear huh? I been trying to figure how to run it this way when the kickdown goes on.

------------------
'69 G.M.C. 350/350. Trying to clean up the left over damage from the Dope-Smokin-Old-Man
I've been dubbed the Longhorn Freak/Fanatic/Expert, I just hope I can live up to it.
FINALLY got the HORNIAC...a '70 one ton Longhorn with a Pontiac 350/350 and lots of 'personality'. Check out The Longhorn Webite.
If you need a pic posted, E-mail me at longhornmail@yahoo.com
Andy, in Columbus Ohio