The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   The 1967-1972 Chevrolet & GMC Pickups Parts Board (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=8)
-   -   AZ Two 1967 Dash harnesses for gauges and a/c (https://67-72chevytrucks.com/vboard/showthread.php?t=608455)

mahanian 12-17-2013 08:36 PM

Two 1967 Dash harnesses for gauges and a/c
 
1 Attachment(s)
I have a pair of 67 dash harnesses out of Arizona trucks. I was going to make one good harness out of both because one has been cut a lot and the other I had to cut the plastic at the firewall to get it out. It's a bit of work but it will save you a good amount of money over the cost of a new one. $25 shipped for the pair

mahanian 12-20-2013 08:39 PM

Re: Two 1967 Dash harnesses for gauges and a/c
 
Let's try $30 for both, good parts to repair a damaged one as well. These are the same harnesses for 1968 as well

mahanian 12-21-2013 06:51 PM

Re: Two 1967 Dash harnesses for gauges and a/c
 
4 Attachment(s)
Here are a few pictures of the better harness, no connectors have been cut off. The ignition connector will need to be replaced because the clips broke off. This is the one that I had to cut at the firewall.

mahanian 12-23-2013 11:23 AM

Re: Two 1967 Dash harnesses for gauges and a/c
 
bump

mahanian 12-25-2013 07:14 PM

Re: Two 1967 Dash harnesses for gauges and a/c
 
ttt

19Chevy67C10 12-26-2013 02:33 AM

Re: Two 1967 Dash harnesses for gauges and a/c
 
Can I get a picture of what you had to cut to remove this harness? And also is this a 67 specific harness. I will take it if it isn't sawed off at the main bulk head meaning from outside to inside. I would hate to have to pull every wire out to re-install them into another good fuse block..I guess a better way to describe is I'm looking for the inside main under dash harness not cut up or ruined on the side that goes though to the firewall. I can replace the ignition part of the harness easy enough...

Thanks and Merry Christmas.

Kev.

mahanian 12-26-2013 12:09 PM

Re: Two 1967 Dash harnesses for gauges and a/c
 
The last picture in post #3 shows where it was cut, which was at the bulkhead. The bolt that holds the engine harness to the dash harness at the firewall stripped out so I had to cut through it.

mahanian 12-30-2013 04:43 PM

Re: Two 1967 Dash harnesses for gauges and a/c
 
I'd hate to recycle these for the copper if someone can use them, how about $25 shipped? That will cover shipping and gas to drop off the box.

mahanian 02-14-2014 02:03 PM

Re: Two 1967 Dash harnesses for gauges and a/c
 
ttt

Grumpy old man 02-14-2014 02:35 PM

Re: Two 1967 Dash harnesses for gauges and a/c
 
$20.00 shipped ? to 37918

mahanian 02-14-2014 03:10 PM

Re: Two 1967 Dash harnesses for gauges and a/c
 
$25 shipped is as low as I can go

mahanian 03-11-2014 08:37 PM

Re: Two 1967 Dash harnesses for gauges and a/c
 
Bump

jabborabbo 03-11-2014 08:43 PM

Re: Two 1967 Dash harnesses for gauges and a/c
 
You wore me down. I'll take 'me for $25 shipped. Let me know how you want payment.

mahanian 03-11-2014 11:05 PM

Re: Two 1967 Dash harnesses for gauges and a/c
 
PM sent


All times are GMT -4. The time now is 08:33 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright 1997-2025 67-72chevytrucks.com