The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   The 1967 - 1972 Chevrolet & GMC Pickups Message Board (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=3)
-   -   Help with buying a clutch (https://67-72chevytrucks.com/vboard/showthread.php?t=763514)

67chevemall 05-09-2018 01:41 PM

Help with buying a clutch
 
Clutch is slipping more and more.
Time to get a new one.
How do I find out if I need a 10.5 ,11 or 12 inch ?
The ram hdx88760 and hdx88762 look like a good buy.
I have a 327 3speed to buy for.
Still not sure if it is saginaw or muncie
Any advice for a first time is welcome.

BCOWANWHEELS 05-09-2018 05:18 PM

Re: Help with buying a clutch
 
get oriellys, there life time guaranteed. put back what comes out.....organic

RustyBucket 05-09-2018 09:22 PM

Re: Help with buying a clutch
 
Guess your gonna have to disassemble it & look. Just ol' greasy nuts & bolts. Pretty straight forward, nice to have a lift & air tools. Done quite a few on the ground with hand tools. Might have to buy/borrow a pilot shaft tool to align the new disc & pressure plate & disc. Probably good youtube. Have fun !! ...... be a good idea to have the flywheel resurfaced..

BCOWANWHEELS 05-09-2018 10:40 PM

Re: Help with buying a clutch
 
YOU don't have to pull tranny, just slide it back about 8 in. change pilot bushing and t/o bearing. alignment tool will come with kit. if clutch has been sliping a lot you probably need a flywheel too. cast iron is fine.

BCOWANWHEELS 05-09-2018 10:43 PM

Re: Help with buying a clutch
 
check / grease u-joints n hanger bearing

67chevemall 05-10-2018 09:54 AM

Re: Help with buying a clutch
 
Take it all apart and measure the clutch size or drop it off and swipe the visa.....humm

67chevemall 05-11-2018 10:56 AM

Re: Help with buying a clutch
 
Trying to find out what I have.
Been reading goggle for 2 hours now.
I think it is the m13 muncie but not sure.
It is cast with 7 bolts and has on the cover plate
M3 3868632
A my build sheet says m13 3 speed sync

Any ideas

BCOWANWHEELS 05-16-2018 04:30 PM

Re: Help with buying a clutch
 
std Saginaw or Muncie 3 speed, gm used both and there interchangeable

mike16 05-17-2018 10:18 PM

Re: Help with buying a clutch
 
you must remove the flywheel and resurface it. no "ought to" about it. if you dont it often does not last 10-15k more miles and it will not be covered by any warrenty

67chevemall 05-18-2018 08:10 AM

Re: Help with buying a clutch
 
Thanks again. It is definitely soaked in oil.
Not sure if I blew the main seal or my red neck oil
Spraying or both did it in.
Going to try 3 cans of brake cleaner before I tear it all apart.


All times are GMT -4. The time now is 05:30 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.
Copyright 1997-2025 67-72chevytrucks.com