The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   The 1960 - 1966 Chevrolet & GMC Pickups Message Board (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=6)
-   -   Door window bump stops (https://67-72chevytrucks.com/vboard/showthread.php?t=822969)

forestb 06-21-2021 03:54 PM

Door window bump stops
 
I know that there was a thread about his before. I think I even commented on it but I can't find it.

I am looking for the bumpers that are mounted inside the door that keep the window from rolling down too far.

val1gonzales 06-21-2021 06:00 PM

Re: Door window bump stops
 
Are you thinking of these? That go inside the door that the window rests on when opened. This is what I used on my 66.
https://www.classicparts.com/1967-72...ctinfo/18-360/

forestb 06-21-2021 06:18 PM

Re: Door window bump stops
 
yes but for some reason I remember it having two attachment points

The Rocknrod 06-21-2021 08:09 PM

Re: Door window bump stops
 
It's a single stop in the door below the glass, it has a hole in it for a rubber bumper (stop). I showed it in the assembly manual in one of these threads (page 361, item #4). Where to purchase - https://www.steelerubber.com/multi-p...per-33-0459-42
http://67-72chevytrucks.com/vboard/a...1&d=1616350467

forestb 06-21-2021 10:21 PM

Re: Door window bump stops
 
Were you the one discussing this on a different thread?

That link didn’t work

The Rocknrod 06-21-2021 10:40 PM

Re: Door window bump stops
 
Quote:

Originally Posted by forestb (Post 8935130)
Were you the one discussing this on a different thread?

That link didn’t work

Yes I was.

forestb 06-21-2021 10:42 PM

Re: Door window bump stops
 
Quote:

Originally Posted by val1gonzales (Post 8935011)
Are you thinking of these? That go inside the door that the window rests on when opened. This is what I used on my 66.
https://www.classicparts.com/1967-72...ctinfo/18-360/

That looks about right according to the door diagram that was posted.

forestb 07-08-2021 09:01 PM

Re: Door window bump stops
 
I could not find the bracket in the door of my 62. I am trying to figure out how to keep the window from going to far down into the door. When I took my electric window mechanism out to fix a different problem the window now goes even deeper into the door than when I took it apart. It still rolls all the way up which is good. I probably will have to take it apart again.

The Rocknrod 07-08-2021 09:17 PM

Re: Door window bump stops
 
Is there a way to place a stop on the power window track?

forestb 07-08-2021 09:28 PM

Re: Door window bump stops
 
It has a Scissor type mechanism. Vary similar to the original type. The only track it runs through are the two on both sides that the original window runs through. I was thinking I might try to add some type of stop on one of those.

The Rocknrod 05-07-2022 07:33 PM

Re: Door window bump stops
 
I just looked in the Truck Shop catalog and found the "door window stops" p/n 60-07601.
Page 74 - https://issuu.com/truckandcarshop/docs/ts_60-72_web


All times are GMT -4. The time now is 02:40 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.
Copyright 1997-2025 67-72chevytrucks.com