![]() |
|
![]() |
#1 |
Registered User
Join Date: Jul 2008
Location: Tracy Ca
Posts: 171
|
Brakes always On???
I have a 1972 1/2 ton 4x4. I replaced master cylinder about 5 weeks ago due to a soft pedal. Now I noticed a brake smell and a drag a few days ago? It looks like the front brakes are staying engaged some not locking but a drag sometimes harder than other times. Could this be a proportioning valve? Any advice?? Thanks
|
![]() |
![]() |
![]() |
#2 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
Re: Brakes always On???
There should have neen a paper in the box telling you about how to adjust the pushrod. You need to shorten the pushrod just a 'lilbit.
You sure it's the front, and not the rear brakes dragging? I've always had the rears drag in this scenerio |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Jul 2008
Location: Tracy Ca
Posts: 171
|
Re: Brakes always On???
Thanks for the response. But I do not understand?? The push rod for the master cylinder? There was info to prime. Do I grind the rod to shorten? How much? 1/8" too much?? Sorry for posting in wrong forum thanks for moving..
Last edited by gary2232; 02-01-2009 at 01:17 PM. |
![]() |
![]() |
![]() |
#4 |
I am a Referee of life.
Join Date: Jun 2000
Location: Greensboro N.C.
Posts: 13,993
|
Re: Brakes always On???
There's an adjustment under the dash.It's a threaded nut/rod.I didn't think to take a pic of mine when I had it on the bench but it would be handy since you can usually only do this by Braille.Basically you shorten the length of the rod by screwing it in then tightening the jsam nut.
__________________
The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil" |
![]() |
![]() |
![]() |
#5 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
Re: Brakes always On???
power brakes, or manual? The adjustment differs between the two.
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Jul 2008
Location: Tracy Ca
Posts: 171
|
Re: Brakes always On???
Power Brakes Any setup info you have or advice will help Thanks Longhorn
Last edited by gary2232; 02-02-2009 at 11:12 AM. |
![]() |
![]() |
![]() |
#7 |
BOHICA
Join Date: Mar 2008
Location: Stewartville, MN
Posts: 440
|
Re: Brakes always On???
Did you replace the pads/rotors/calipers at the same time? I replaced the pads and rotors on my little work beater a couple months ago and had the same issue. What I found was a little rust spot on the pins that the calipers slide on. It wasn't allowing the brakes to fully release and they would drag for a little while. Warped a brand new set of rotors before I figured it out.
__________________
Trying to save someone from their own stupidity is like teaching a pig to dance. It is a waste of your time, and it annoys the pig! |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Jul 2008
Location: Tracy Ca
Posts: 171
|
Re: Brakes always On???
Did the rears last year and fronts checked ok. Thanks
|
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Jul 2008
Location: Tracy Ca
Posts: 171
|
Re: Brakes always On???
OK found in book that 1/8" lash in pedal travel I have 1/2" Any short cuts to removing linkage? The bolt through pedal arm will not come out because of steering column. I was thinking of opening a bleed valve to allow pedal to go to floor to remove bolt??? Any ideas???
|
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|