|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
07-08-2015, 05:01 PM
|
#1 |
|
Registered User
Join Date: Feb 2015
Location: Georgetown, TX
Posts: 5
|
Tuck wont start after replacing valve cover gaskets!
i have a 1982 chevy pickup and i just replaced my valve cover gaskets and when i went start the engine all it did was turn over but did not start. i have the right amount of oil, gas and the battery is good. i checked all my hoses and vacuum lines and they are good also. Whats wrong?
|
|
|
|
07-08-2015, 05:32 PM
|
#2 |
|
Slots go on anything!
Join Date: May 2003
Location: Richardson, TX
Posts: 5,957
|
Re: Tuck wont start after replacing valve cover gaskets!
Make sure you didn't accidentally bump the power wire for the distributor.
__________________
1974 Jimmy- 5.3/4L80e/NP241 |
|
|
|
|
07-08-2015, 06:04 PM
|
#3 |
|
Registered User
Join Date: Nov 2014
Location: Connecticut
Posts: 51
|
Re: Tuck wont start after replacing valve cover gaskets!
try a squirt of starting fluid
__________________
Grandpa's '87 Sierra R1500. |
|
|
|
|
07-09-2015, 12:35 AM
|
#4 | |
|
Registered User
Join Date: May 2014
Location: North AL
Posts: 363
|
Re: Tuck wont start after replacing valve cover gaskets!
Quote:
__________________
http://i204.photobucket.com/albums/b...baae5d9a7e.jpg |
|
|
|
|
|
07-09-2015, 06:12 AM
|
#5 |
|
Senior Member
 
Join Date: Jun 2015
Location: Atlanta, GA.
Posts: 737
|
Re: Tuck wont start after replacing valve cover gaskets!
Check each plug wire is routed to the correct plug. Every time my nephew touches a plug wire, he crosses them up. No matter how careful he is, it always happens.
__________________
Jay Gesner Atlanta, GA 1985 C10 Long Bed 4X2 LS 5.3, 4L60E Father/Daughter Project |
|
|
|
|
07-09-2015, 07:47 AM
|
#6 |
|
Registered User
Join Date: Aug 2011
Location: Gallatin, TN
Posts: 782
|
Re: Tuck wont start after replacing valve cover gaskets!
I bet you used the wrong valve cover gaskets.....
Sorry, had to do it. Check to see if you have spark at the plugs.
__________________
77 C10, 6.0LS/4L80E, 3:73 12 bolt. Boss 338's 20" x 10" w/ 285/50/20 rear. 20" x 8.5" w/ 245/40/20 front. Vintage Air. Full Autometer gauges recessed in factory bezel (Thanks bigblock73!) Gm Storm Grey Metallic paint "Cool ain't ever cheap and cheap ain't ever cool" |
|
|
|
|
07-10-2015, 01:19 AM
|
#7 |
|
Registered User
Join Date: Feb 2015
Location: Georgetown, TX
Posts: 5
|
Re: Tuck wont start after replacing valve cover gaskets!
Hey guys thanks for all the input it just so happened to be that all I had to do was put a little bit of gas in my carb. It had been setting a while because I've been so busy so I'm sure some of that gas evaporated.
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
