73-87 DBW pedal bracket?

[Nodnarb76]

What is everyone doing to mount the DBW pedal in there 73-87 trucks?
I've seen Hart Rods killer throttle brackets for the 76-72 trucks and when I contacted him, he unfortunately doesn't make them for our trucks.

[Houston Ben]

Depending on what year you have, I replaced my 2011 truck pedal for a Corvette pedal and used Hart Rod's plate and it works perfect! All I had to do was swap two pins in the plug for the pedal.

[Nodnarb76]

Are the mounting locations different for each pedal?
Sounds like I'll be getting a pedal from a 03-06 truck (Pedal is still being shipped with the motor so I can't be sure until I get it).
would love to get one of Hart Rod's adapters if it will work. I don't mind drilling if I need to, but as far as cutting or bending the bracket, I'm worried I won't be able to get it right.

[Tilt]

The '04 DBW truck pedal I used had 2 bolt holes that lined up with the original pedal holes. Haven't had any issues using just two bolts.

[NorCalAnthony]

There's a few people using the pedal from a late 90's 6.5 diesel on their Gen III setups. You have to swap a couple of wires in the harness but the pedal itself bolts right up in the 73-87(91) trucks. Here's a pretty good write up on it:

http://api.viglink.com/api/click?for...1%2520swap.pdf

[wildwilly4x4]

I used a '95 6.5 diesel pedal. bolted right in. had to repin the connector on a couple of wires IIRC. Looks completely stock

[Hart_Rod]

Originally Posted by NorCalAnthony

There's a few people using the pedal from a late 90's 6.5 diesel on their Gen III setups. You have to swap a couple of wires in the harness but the pedal itself bolts right up in the 73-87(91) trucks. Here's a pretty good write up on it:

http://api.viglink.com/api/click?for...1%2520swap.pdf

Originally Posted by wildwilly4x4

I used a '95 6.5 diesel pedal. bolted right in. had to repin the connector on a couple of wires IIRC. Looks completely stock

Good info guys!!! I just added this to my DBW pedal thread so the 73-87 guys can get their conversion done as easily as possible, .

[solidaxel]

Originally Posted by Nodnarb76

Are the mounting locations different for each pedal?
Sounds like I'll be getting a pedal from a 03-06 truck (Pedal is still being shipped with the motor so I can't be sure until I get it).
would love to get one of Hart Rod's adapters if it will work. I don't mind drilling if I need to, but as far as cutting or bending the bracket, I'm worried I won't be able to get it right.

Cut and bend it for Your Foot!
These peddles (DBW) do not have much movement to reach 100% throttle

[dman1982]

in my build somewhere i believe i got a pic of my dbw setup, i did some cutting and welding to make mine work, turned out pretty good

[Nodnarb76]

This is the pedal that came with my swap, what would be needed to bolt it up to my 87 Burb? Do I need to bend the pedal bracket or mod one of Hart Rod's brackets?
Thanks again

[Pulse_GTO]

What about GEN IV pedals that don't make use of a TAC module?

[Hart_Rod]

Originally Posted by Pulse_GTO

What about GEN IV pedals that don't make use of a TAC module?

What year is your truck and pedal?

[Liltroy]

http://67-72chevytrucks.com/vboard/s...3&page=1306-07 is a plastic pedal. post 302 shows what I did. Got the idea from glock35. Used the left hand original hole in the bottom pedal hole then drilled a new hole for top pedal hole.

[Nodnarb76]

About to buy the 98 6.5 diesel pedal, if I re-wire the connector like the above link says, this should work with a 2004 gen3 PCM and TAC module right?

[Nodnarb76]

Ok bought a new pedal from Rock Auto, instead of taking a chance in screwing up my existing harness, I'm going to see of I can find another pedal harness to buy and modify, just in case something gets messed up.

[Nodnarb76]

Bringing this post back from the dead.
I never did try to re-work my pedal/harness wiring. I was too afraid of screwing something up.
Has anyone been able to use one of Hart Rod's 67-72 brackets for a 73-87 truck with a little work?
I have my pedal working in my truck now, but it sits way too high up, and is un-comfortable to drive for a long time.

[homemade87]

Originally Posted by Nodnarb76

Bringing this post back from the dead.
I never did try to re-work my pedal/harness wiring. I was too afraid of screwing something up.
Has anyone been able to use one of Hart Rod's 67-72 brackets for a 73-87 truck with a little work?
I have my pedal working in my truck now, but it sits way too high up, and is un-comfortable to drive for a long time.

Nodnard76 , This may help. I used an 04 truck pedal . The o4 was a medal bracket . If I remember correctly you had one with a metal pedal arm like I used . I think I used 2 holes that were already there in my 82 to bolt it to the floor . I cut the metal arm off and drilled a hole in it and cut the 82 pedal arm off and inserted it into the 04 arm and set it in place to position it and welded it in place . It is a perfect fit for me . Also looks just like the oem pedal . Heres a couple pictures .

[Nodnarb76]

Originally Posted by homemade87

Nodnard76 , This may help. I used an 04 truck pedal . The o4 was a medal bracket . If I remember correctly you had one with a metal pedal arm like I used . I think I used 2 holes that were already there in my 82 to bolt it to the floor . I cut the metal arm off and drilled a hole in it and cut the 82 pedal arm off and inserted it into the 04 arm and set it in place to position it and welded it in place . It is a perfect fit for me . Also looks just like the oem pedal . Heres a couple pictures .

That is a good idea, I have a question though as I know nothing about welding.
I am worried that welding my pedal will get the pedal too hot and mess up the electronics in the pedal. Do I not need to worry about that? If not I have a friend who can weld for me and I may end up doing what you did.

[homemade87]

Originally Posted by Nodnarb76

That is a good idea, I have a question though as I know nothing about welding.
I am worried that welding my pedal will get the pedal too hot and mess up the electronics in the pedal. Do I not need to worry about that? If not I have a friend who can weld for me and I may end up doing what you did.

It was not a problem for me . It was not much more than a tack weld . Once done cool it with water . The electronics was far enough away it did not affect them .

[Nodnarb76]

Originally Posted by homemade87

It was not a problem for me . It was not much more than a tack weld . Once done cool it with water . The electronics was far enough away it did not affect them .

Thank you! I just talked to my friend with the welder and we are going to do this next weekend just like you did. I will post back when I'm done.

[StingRay]

As I understand it some of the the 72's use the later bolt pattern of the 73-87. The rework is to just drill another hole in the bracket. I think the current ones have both hole sets.

[TooTall]

Here's my scrap pedal mount. It's at the 3:55 mark.

73 K5 blazer with the DBW pedal mount, using the stock pedal

I used a flat stock of plate, and moved it over 3" and that was it.

https://youtu.be/5oHGKGFrVzw

[77c10bowtie]

Likuid kerations Has the absolute best dbw pedal brackets for 60-66 67-72 and 73-87 for all 3 pedal styles. Got one of their 67-72 and 73-87 and they are seriously top quality. I struggled to find a good bracket for 73-87 and now I know there isn't a better bracket out there. Best part is they are only $50 bucks

[87chevy.com]

Gen5 swap - Ive done 2 different pedals. Stock Gen5 truck/Tahoe pedal and while it doesn't look like stock, it doesn't look bad. I still haven't made a metal bracket, still out of 3/4 MDF.

Other I used a 2008 Impala pedal and modified it to use the stock C10 pedal. The Impala needed to have a little sheet metal plate cut out so the pedal would have the stock c10 tilt, otherwise, it was a lot more vertical if i remember, really awkward.

clint