CA WTB 5 lug axles - The 1947 - Present Chevrolet & GMC Truck Message Board Network

shawno72 · 11-08-2012, 01:18 AM

I know this is probably a long shot but I'll give it a try. I am looking for a set of 5 lug axles or conversion axles for my 68 rear end. They obviously need to be for the narrow rear end. Let me know what you have and how much shipping would be to a 95240 business address. Please respond in thread.
Posted via Mobile Device

ortegamotor · 11-08-2012, 09:52 AM

I have a set..... I'll just need to make sure they're the right size. I actually have two sets. do you know how long they need to be?

shawno72 · 11-08-2012, 10:06 AM

Actually I don't but I know they are shorter than the later 70-72 axles and I have a set of those so let me measure them and we will go from there. I'm guessing since the early axle housing is 1 1/2" short then the axle should be 3/4" shorter?
Posted via Mobile Device

CC69Rat · 11-08-2012, 10:55 AM

I looked at mine (Moser, for the late rear end) and they are 31 5/16 "

.. but the Moser for the early rear end shows 30 1/2 "

Adding 3/4 per side that's within 1/16". 30.5 + .75 = 31.25 (31 1/4") I will tell ya, when I put the pin back in mine , the tolerances were spot on. You couldn't get it any closer. Just a light bump to get the pin to go back between the axle ends, but you could push it back out with your finger. It was definitely not as loose as with the original 6 luggers.

So, I'm thinking the shorties are 30.5" long per side. That help? Running stock 5 lug axles, you should be really close with 30.5"

Mosers are $260 + bearings and seals. Just FYI.

shawno72 · 11-08-2012, 11:02 AM

Thanks Chad that helps a bunch. Where did you buy your Mosers from? Tony what do your axles measure?
Posted via Mobile Device

CC69Rat · 11-08-2012, 11:39 AM

Ordered mine straight from MEng. Super happy with them. 1/2 in studs, just FYI.
Posted via Mobile Device

shawno72 · 11-08-2012, 12:17 PM

Quote:

Originally Posted by CC69Rat

Ordered mine straight from MEng. Super happy with them. 1/2 in studs, just FYI.
Posted via Mobile Device

Is 1/2 studs the stock size and do they come with lug nuts?

**cericd** · 11-08-2012, 12:27 PM

Hey Shawn and Chad. Got a question for y'all. I recently measured the rear end on my '70 C10. Turns out, it's the wider one. I plan to do the five lug swap too so would Shawn's longer set work for me (assuming you're looking for the shorter set as a replacement)?

shawno72 · 11-08-2012, 12:38 PM

Quote:

Originally Posted by cericd

Hey Shawn and Chad. Got a question for y'all. I recently measured the rear end on my '70 C10. Turns out, it's the wider one. I plan to do the five lug swap too so would Shawn's longer set work for me (assuming you're looking for the shorter set as a replacement)?

Yes and no.

For you the swap will be easy, just find a 71-72 5 lug rear end and steal the axles. I have the early 6 lug rear end which is narrower to start so I need a set of aftermarket conversion axles. Sorry I can't help you there.

CC69Rat · 11-08-2012, 01:56 PM

You'd need the longer version axles. (same as mine Chris) Stock / Aftermarket .. either way. Same legth.

7/16 is stock Shawn. 1/2 is usually Ford. My truck is all 1/2 now. So, saying if you do Mosers you will likely need new lugs too.

**lolife99** · 11-08-2012, 02:21 PM

Quote:

Originally Posted by CC69Rat

You'd need the longer version axles. (same as mine Chris) Stock / Aftermarket .. either way. Same legth.

7/16 is stock Shawn. 1/2 is usually Ford. My truck is all 1/2 now. So, saying if you do Mosers you will likely need new lugs too.

7/16" is stock for pre-'71 6-lug trucks.
1/2" is stock for 71-87 5-lug trucks.

shawno72 · 11-08-2012, 02:29 PM

Quote:

Originally Posted by CC69Rat

You'd need the longer version axles. (same as mine Chris) Stock / Aftermarket .. either way. Same legth.

7/16 is stock Shawn. 1/2 is usually Ford. My truck is all 1/2 now. So, saying if you do Mosers you will likely need new lugs too.

Quote:

Originally Posted by lolife99

7/16" is stock for pre-'71 6-lug trucks.
1/2" is stock for 71-87 5-lug trucks.

Thanks guys, I knew there was a differance between the 5 and the 6 lug, I just couldn't remember which way it was

CC69Rat · 11-08-2012, 01:57 PM

Lug nuts sold seperately.. Some assembly required.

(studs are pressed in when you get them too)

shawno72 · 11-08-2012, 04:47 PM

I found this on the Summit website, looks like I need the 30 1/2" axles.
http://www.summitracing.com/parts/ms...del/c10-pickup

CC69Rat · 11-08-2012, 04:55 PM

Yep.. they're sweet man.

shawno72 · 11-08-2012, 05:49 PM

Will the stock bearing work? I just put in new seals and bearings and would hate to buy new ones if I didn't have to.

CC69Rat · 11-08-2012, 06:02 PM

Yeah.. if theyre new, Id think youre good. The ones I got from Moser were just Napa bearings. Id say theyre just stock spec but maybe call and ask to be sure?
Posted via Mobile Device

shawno72 · 11-08-2012, 06:15 PM

I will, thanks Chad. Tony put down the wrenches for a moment and take a measurement

shawno72 · 11-09-2012, 02:24 PM

ttt looking for a pair of 30.5" 5 lug axles

CC69Rat · 11-09-2012, 03:05 PM

Most shorties out there will all be 6 lug. Id say if they are short 5 lug, theyre likely aftermarket.
Posted via Mobile Device

shawno72 · 11-09-2012, 03:40 PM

Quote:

Originally Posted by CC69Rat

Most shorties out there will all be 6 lug. Id say if they are short 5 lug, theyre likely aftermarket.
Posted via Mobile Device

Yeah I'm almost positive they are gonna be aftermarket, I was just hoping to catch someone maybe going a different direction with their build or ordered the wrong set or just wanting to help a brother out.....

CC69Rat · 11-09-2012, 03:42 PM

Buy my 68 step. It has some in it.

. 3:73 too...
Posted via Mobile Device

HotRod C/10 · 11-09-2012, 03:47 PM

I got my mosers for short diff at Summit Racing.
Posted via Mobile Device

shawno72 · 11-09-2012, 03:47 PM

I just sold my 3.73 gear set

No chance of parting that thing out, huh??

ortegamotor · 11-09-2012, 03:58 PM

Dude I totally dropped the ball. I just ran out to the shop to measure those axls they look to be 30.5 I think thats what you're looking for . PM me for info and my #

Tony

11-08-2012, 01:18 AM	#1
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	WTB 5 lug axles I know this is probably a long shot but I'll give it a try. I am looking for a set of 5 lug axles or conversion axles for my 68 rear end. They obviously need to be for the narrow rear end. Let me know what you have and how much shipping would be to a 95240 business address. Please respond in thread. Posted via Mobile Device __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

11-08-2012, 09:52 AM	#2
ortegamotor Registered User Join Date: Jun 2006 Location: auburn california Posts: 1,147	Re: WTB 5 lug axles I have a set..... I'll just need to make sure they're the right size. I actually have two sets. do you know how long they need to be? __________________ ORTEGAMOTOR

11-08-2012, 10:06 AM	#3
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: WTB 5 lug axles Actually I don't but I know they are shorter than the later 70-72 axles and I have a set of those so let me measure them and we will go from there. I'm guessing since the early axle housing is 1 1/2" short then the axle should be 3/4" shorter? Posted via Mobile Device __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

11-08-2012, 10:55 AM	#4
CC69Rat Registered User Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,210	Re: WTB 5 lug axles I looked at mine (Moser, for the late rear end) and they are 31 5/16 " .. but the Moser for the early rear end shows 30 1/2 " Adding 3/4 per side that's within 1/16". 30.5 + .75 = 31.25 (31 1/4") I will tell ya, when I put the pin back in mine , the tolerances were spot on. You couldn't get it any closer. Just a light bump to get the pin to go back between the axle ends, but you could push it back out with your finger. It was definitely not as loose as with the original 6 luggers. So, I'm thinking the shorties are 30.5" long per side. That help? Running stock 5 lug axles, you should be really close with 30.5" Mosers are $260 + bearings and seals. Just FYI. __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

11-08-2012, 11:02 AM	#5
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: WTB 5 lug axles Thanks Chad that helps a bunch. Where did you buy your Mosers from? Tony what do your axles measure? Posted via Mobile Device __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

11-08-2012, 11:39 AM	#6
CC69Rat Registered User Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,210	Re: WTB 5 lug axles Ordered mine straight from MEng. Super happy with them. 1/2 in studs, just FYI. Posted via Mobile Device __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

11-08-2012, 12:27 PM	#8
cericd Senior Member Join Date: Jan 2012 Location: Texan, back in TX Posts: 2,158	Re: WTB 5 lug axles Hey Shawn and Chad. Got a question for y'all. I recently measured the rear end on my '70 C10. Turns out, it's the wider one. I plan to do the five lug swap too so would Shawn's longer set work for me (assuming you're looking for the shorter set as a replacement)?

11-08-2012, 01:56 PM	#10
CC69Rat Registered User Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,210	Re: WTB 5 lug axles You'd need the longer version axles. (same as mine Chris) Stock / Aftermarket .. either way. Same legth. 7/16 is stock Shawn. 1/2 is usually Ford. My truck is all 1/2 now. So, saying if you do Mosers you will likely need new lugs too. __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

11-08-2012, 01:57 PM	#13
CC69Rat Registered User Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,210	Re: WTB 5 lug axles Lug nuts sold seperately.. Some assembly required. (studs are pressed in when you get them too) __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

11-08-2012, 04:47 PM	#14
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: WTB 5 lug axles I found this on the Summit website, looks like I need the 30 1/2" axles. http://www.summitracing.com/parts/ms...del/c10-pickup __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

11-08-2012, 04:55 PM	#15
CC69Rat Registered User Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,210	Re: WTB 5 lug axles Yep.. they're sweet man. Attached Images __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

11-08-2012, 05:49 PM	#16
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: WTB 5 lug axles Will the stock bearing work? I just put in new seals and bearings and would hate to buy new ones if I didn't have to. __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

11-08-2012, 06:02 PM	#17
CC69Rat Registered User Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,210	Re: WTB 5 lug axles Yeah.. if theyre new, Id think youre good. The ones I got from Moser were just Napa bearings. Id say theyre just stock spec but maybe call and ask to be sure? Posted via Mobile Device __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

11-08-2012, 06:15 PM	#18
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: WTB 5 lug axles I will, thanks Chad. Tony put down the wrenches for a moment and take a measurement __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

11-09-2012, 02:24 PM	#19
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: WTB 5 lug axles ttt looking for a pair of 30.5" 5 lug axles __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"



Register or Log In To remove these advertisements.

11-09-2012, 03:05 PM	#20
CC69Rat Registered User Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,210	Re: WTB 5 lug axles Most shorties out there will all be 6 lug. Id say if they are short 5 lug, theyre likely aftermarket. Posted via Mobile Device __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

11-09-2012, 03:42 PM	#22
CC69Rat Registered User Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,210	Re: WTB 5 lug axles Buy my 68 step. It has some in it. . 3:73 too... Posted via Mobile Device __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

11-09-2012, 03:47 PM	#23
HotRod C/10 Registered User Join Date: Feb 2012 Location: Albuquerque NM Posts: 3,053	Re: WTB 5 lug axles I got my mosers for short diff at Summit Racing. Posted via Mobile Device __________________ SOLD -77 CHEYENNE SWB, LS SWAPPED -1976 SILVERADO YUBA GOLD/NEUTRAL (2-TONE)

11-09-2012, 03:47 PM	#24
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: WTB 5 lug axles I just sold my 3.73 gear set No chance of parting that thing out, huh?? __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

11-09-2012, 03:58 PM	#25
ortegamotor Registered User Join Date: Jun 2006 Location: auburn california Posts: 1,147	Re: WTB 5 lug axles Dude I totally dropped the ball. I just ran out to the shop to measure those axls they look to be 30.5 I think thats what you're looking for . PM me for info and my # Tony Attached Images __________________ ORTEGAMOTOR

Register or Log In To remove these advertisements.