The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Suspension

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-23-2009, 08:17 PM   #1
MXmaniac
Registered User
 
MXmaniac's Avatar
 
Join Date: Jan 2007
Location: Denton, Texas
Posts: 356
Stepped control arms

I've got one of my control arms stepped 1-1/2". This is my first attempt at real fabrication and modification. I don't think this sucker is ever going to come apart. I used 1/4" steel plate for all the gussets and pieces. Everything went very smoothly and I'm confident that I did a good job. Now I just have to make the other one match, paint them, press in new ball joints, and I can put the front of my '64 back together and see how she sits with the 1-1/2" LCAs and 3" springs.

Oh and if you're wondering why I didn't just use drop spindles its because I'm an 18 year old kid with a tiny budget that can't afford a disk brake swap, let alone new spindles. But I do, however, have a welder and a nice workshop(thanks dad) and a lot of ambition!
Attached Images
     
__________________
Andrew
'69 C-20(292, 4-speed) Retired Daily Driver
'64 C-10(250, 3-speed) Fixerupper
'97 F*rd Mustang GT(4.6L, 5-speed) Daily Driver
If I only wanted two pedals I'd have bought a bicycle.

Last edited by MXmaniac; 03-23-2009 at 08:23 PM.
MXmaniac is offline   Reply With Quote
Old 03-23-2009, 08:19 PM   #2
MXmaniac
Registered User
 
MXmaniac's Avatar
 
Join Date: Jan 2007
Location: Denton, Texas
Posts: 356
Re: Stepped control arms

Here it is next to the stock one that I need to step for the other side.
Attached Images
 
__________________
Andrew
'69 C-20(292, 4-speed) Retired Daily Driver
'64 C-10(250, 3-speed) Fixerupper
'97 F*rd Mustang GT(4.6L, 5-speed) Daily Driver
If I only wanted two pedals I'd have bought a bicycle.
MXmaniac is offline   Reply With Quote
Old 03-23-2009, 08:24 PM   #3
Hottrucks
Redefining LowBudget
 
Hottrucks's Avatar
 
Join Date: Mar 2009
Location: lebanon Cow Hampshire
Posts: 4,538
Re: Stepped control arms

heres a little helper for yea if you check your local hot rod shop or dirt track place where the guys go to build roll cages you can get corner pieces pre fabbed for the corners for stupid cheap and just weld them in..but it lo good..can't wait to see them in the truck
__________________
1970 C10 CST fleetside 472 ....big dreams little cash...
SunShine Syndicate..

Mikes Sandwich Fair Run OCT 8th 2011

Last edited by Hottrucks; 03-23-2009 at 08:25 PM.
Hottrucks is offline   Reply With Quote
Old 03-23-2009, 08:26 PM   #4
MXmaniac
Registered User
 
MXmaniac's Avatar
 
Join Date: Jan 2007
Location: Denton, Texas
Posts: 356
Re: Stepped control arms

Quote:
Originally Posted by Hottrucks View Post
heres a little helper for yea if you check your local hot rod shop or dirt track place where the guys go to build roll cages you can get corner pieces pre fabbed for the corners for stupid cheap and just weld them in..but it lo good..can't wait to see them in the truck
That's a good tip! Oh well, it didn't take too long with a cut-off wheel on an old circular saw.
__________________
Andrew
'69 C-20(292, 4-speed) Retired Daily Driver
'64 C-10(250, 3-speed) Fixerupper
'97 F*rd Mustang GT(4.6L, 5-speed) Daily Driver
If I only wanted two pedals I'd have bought a bicycle.
MXmaniac is offline   Reply With Quote
Old 03-23-2009, 08:35 PM   #5
p8ntballer1911
Bodydropped71
 
p8ntballer1911's Avatar
 
Join Date: Jun 2008
Location: Conroe Texas
Posts: 264
Re: Stepped control arms

Let us know the outcome!
p8ntballer1911 is offline   Reply With Quote
Old 03-23-2009, 10:40 PM   #6
MXmaniac
Registered User
 
MXmaniac's Avatar
 
Join Date: Jan 2007
Location: Denton, Texas
Posts: 356
Re: Stepped control arms

Quote:
Originally Posted by p8ntballer1911 View Post
Let us know the outcome!
Definitely. It might be a week or two though.
__________________
Andrew
'69 C-20(292, 4-speed) Retired Daily Driver
'64 C-10(250, 3-speed) Fixerupper
'97 F*rd Mustang GT(4.6L, 5-speed) Daily Driver
If I only wanted two pedals I'd have bought a bicycle.
MXmaniac is offline   Reply With Quote
Old 03-23-2009, 11:11 PM   #7
N2TRUX
Happy to be here
 
N2TRUX's Avatar
 
Join Date: Mar 2000
Location: Cypress, TX
Posts: 39,023
Re: Stepped control arms

Quote:
Originally Posted by MXmaniac View Post
.....Oh and if you're wondering why I didn't just use drop spindles its because I'm an 18 year old kid with a tiny budget that can't afford a disk brake swap, let alone new spindles. But I do, however, have a welder and a nice workshop(thanks dad) and a lot of ambition!
Awesome! Glad to see ambitious young builders jump in the mix. Be sure to let the old man check the integrity of your welds. They look good from here, but it's best to have someone with a trained eye look things over.

Also keep in mind that you have lowered the scrub line considerably. You didn't mention what size wheels you plan to run, but this could be in issue with a small diameter rim is a flat occurs.

Keep the progress pics coming.
__________________
Follow me on Facebook and Instagram @N2trux.com

Articles-

"Jake" the 84 to 74 crewcab

"Elwood" the77_Remix

85 GMC Sierra "Scarlett"

"Refining Sierra"
N2TRUX is offline   Reply With Quote
Old 03-23-2009, 11:32 PM   #8
MXmaniac
Registered User
 
MXmaniac's Avatar
 
Join Date: Jan 2007
Location: Denton, Texas
Posts: 356
Re: Stepped control arms

Quote:
Originally Posted by N2TRUX View Post
Awesome! Glad to see ambitious young builders jump in the mix. Be sure to let the old man check the integrity of your welds. They look good from here, but it's best to have someone with a trained eye look things over.

Also keep in mind that you have lowered the scrub line considerably. You didn't mention what size wheels you plan to run, but this could be in issue with a small diameter rim is a flat occurs.

Keep the progress pics coming.
I've gotten the green light from my dad(he didn't like the idea of cutting them up and welding them back together, but now that he sees them he says they look stronger than before) and several others. I'm taking a welding course at school and it has definitely taught me a lot and I have way more confidence now.

And the scrub line issue is why I only stepped them 1-1/2"(well, that and bumpsteer concerns). I'll be running 15" wheels but it should be fine. If I'm not mistaken(I very well could be), I'll have 1" more clearance, as far as scrub line is concerned, than if I had used 2-1/2" drop spindles. Correct?
__________________
Andrew
'69 C-20(292, 4-speed) Retired Daily Driver
'64 C-10(250, 3-speed) Fixerupper
'97 F*rd Mustang GT(4.6L, 5-speed) Daily Driver
If I only wanted two pedals I'd have bought a bicycle.
MXmaniac is offline   Reply With Quote
Old 03-29-2009, 03:11 PM   #9
MXmaniac
Registered User
 
MXmaniac's Avatar
 
Join Date: Jan 2007
Location: Denton, Texas
Posts: 356
Re: Stepped control arms

Here's the end result. Painted and fresh ball joints installed.
Attached Images
  
__________________
Andrew
'69 C-20(292, 4-speed) Retired Daily Driver
'64 C-10(250, 3-speed) Fixerupper
'97 F*rd Mustang GT(4.6L, 5-speed) Daily Driver
If I only wanted two pedals I'd have bought a bicycle.
MXmaniac is offline   Reply With Quote
Old 03-29-2009, 03:16 PM   #10
project 67 sub
Account Suspended
 
project 67 sub's Avatar
 
Join Date: Mar 2007
Location: san bernardino ca. everywhere
Posts: 3,938
Re: Stepped control arms

looks good
project 67 sub is offline   Reply With Quote
Old 03-29-2009, 03:55 PM   #11
Inverter
Registered User
 
Inverter's Avatar
 
Join Date: Mar 2007
Location: East Texas
Posts: 429
Re: Stepped control arms

Thats cool. When I was 18 I could barely check my oil. Stay w/it and you could be the next Trepanier.
__________________
TROY
My work ~ https://www.67-72chevytrucks.com/vbo...d.php?t=799484

Last edited by Inverter; 03-29-2009 at 03:57 PM.
Inverter is offline   Reply With Quote
Old 03-29-2009, 03:48 PM   #12
duceducenine
Registered User
 
duceducenine's Avatar
 
Join Date: Nov 2006
Location: el sobrante CA 94803
Posts: 284
Re: Stepped control arms

looks great i always wanted to do a set of these
but to also shorten them 1.5" to compensate for
camber for the lowered stance with the dropped
coils! any insights?
duceducenine is offline   Reply With Quote
Old 04-06-2009, 07:21 PM   #13
Hard Luck
I've got grease on my mind.
 
Hard Luck's Avatar
 
Join Date: Sep 2007
Location: Oly, Wa
Posts: 481
Re: Stepped control arms

Quote:
Originally Posted by duceducenine View Post
looks great i always wanted to do a set of these
but to also shorten them 1.5" to compensate for
camber for the lowered stance with the dropped
coils! any insights?
I just did this mod on my 69. You only have to shorten the arms only about 1/4" not 1-1/2" that would move the arm into the upper spring pocket and bind both of the ball joints. You generally lose that distance in the cut anyway.

As faw as the bumpstops go I am using the new foam style (they have more absorption for the hits and allow a little more give) I will be mounting the to the upper coil towers.

Your work looks great! Keep on truckin'
Hard Luck is offline   Reply With Quote
Old 04-06-2009, 08:03 PM   #14
Hottrucks
Redefining LowBudget
 
Hottrucks's Avatar
 
Join Date: Mar 2009
Location: lebanon Cow Hampshire
Posts: 4,538
Re: Stepped control arms

excuse me for being a newbie to this but the 1/4" you loose from te cut you gain back with the thickness of the plate????...could you put a cut in the bottom of the upper A ram near the ball joint and bend it closed (bend the ball joint mount down) to stop the bind?? and do the same when you cut the bottom??
__________________
1970 C10 CST fleetside 472 ....big dreams little cash...
SunShine Syndicate..

Mikes Sandwich Fair Run OCT 8th 2011
Hottrucks is offline   Reply With Quote
Old 04-08-2009, 02:46 AM   #15
woodwright
Enjoying left field
 
woodwright's Avatar
 
Join Date: Jun 2008
Location: Dillon Montana
Posts: 900
Re: Stepped control arms

(.....could you put a cut in the bottom of the upper A ram near the ball joint and bend it closed (bend the ball joint mount down) to stop the bind?? and do the same when you cut the bottom??.......)

Heres how i did my LCA's.


I ended up making new UCA's
__________________
Clint

70 Chevy 4WD "Ultimate Work Truck" SOLD

Last edited by woodwright; 04-08-2009 at 02:48 AM.
woodwright is offline   Reply With Quote
Old 03-29-2009, 05:22 PM   #16
Hottrucks
Redefining LowBudget
 
Hottrucks's Avatar
 
Join Date: Mar 2009
Location: lebanon Cow Hampshire
Posts: 4,538
Re: Stepped control arms

does someone know if this works for the 66-72 models too???? I'm going to air ride and was going to cup the bags but if this gets me lower than What the heck I'm going to be welding up the lower A arm anyway.....just worried about cross memeber drag , bump steer and camber adjustment??? any input?? thanx Jeff
__________________
1970 C10 CST fleetside 472 ....big dreams little cash...
SunShine Syndicate..

Mikes Sandwich Fair Run OCT 8th 2011
Hottrucks is offline   Reply With Quote
Old 03-29-2009, 05:44 PM   #17
leftcoast66
Registered User
 
leftcoast66's Avatar
 
Join Date: Sep 2006
Location: Covington, WA
Posts: 770
Re: Stepped control arms

Quote:
Originally Posted by Hottrucks View Post
does someone know if this works for the 66-72 models too???? I'm going to air ride and was going to cup the bags but if this gets me lower than What the heck I'm going to be welding up the lower A arm anyway.....just worried about cross memeber drag , bump steer and camber adjustment??? any input?? thanx Jeff
Yes it should work on the 66-72 since its the same suspension. Yes your gonna have an issue w/ crossmember drag, but you will no matter what since its the lowest point on the frame, aside from exhaust and such. No idea on bumpsteer or camber adjustment. Honestly I would instead since your gonna do bags to begin with, build your own cup mounts and do them w/ 8" I think it was pipe so that the bag is set down inside the LCA and not on top of a cup mount. Then once you lay frame, your gonna have an issue and will need to solve that by either zing the frame or going w/ a dropmember from porterbuilt.

Looks good on the work you did. I like the idea of doing all your own fabrication especially at your age. It looks like its gonna be a fun project.
leftcoast66 is offline   Reply With Quote
Old 03-29-2009, 08:34 PM   #18
royo
Registered User
 
royo's Avatar
 
Join Date: Feb 2007
Location: knoxville tn
Posts: 1,013
Re: Stepped control arms

Looking good good luck with it
__________________
nickle and dime
royo is offline   Reply With Quote
Old 03-29-2009, 08:56 PM   #19
MXmaniac
Registered User
 
MXmaniac's Avatar
 
Join Date: Jan 2007
Location: Denton, Texas
Posts: 356
Re: Stepped control arms

Quote:
Originally Posted by duceducenine View Post
looks great i always wanted to do a set of these
but to also shorten them 1.5" to compensate for
camber for the lowered stance with the dropped
coils! any insights?
Yeah after I got started I realized I should have taken a few more measurements to account for the camber. Oh well, live and learn. I think it will be alright. This truck won't be a daily driver or anything so I'm not too worried about some extra tire wear, hopefully the rears will still wear faster than the fronts, if you know what I mean.

I've got heim rod ends coming in the mail so I can alleviate any bumpsteer issues by attaching the tie rods underneath the steering arm.

And thanks for all the kind words guys! Its good to get compliments from people that know their stuff.
__________________
Andrew
'69 C-20(292, 4-speed) Retired Daily Driver
'64 C-10(250, 3-speed) Fixerupper
'97 F*rd Mustang GT(4.6L, 5-speed) Daily Driver
If I only wanted two pedals I'd have bought a bicycle.
MXmaniac is offline   Reply With Quote
Old 03-31-2009, 11:53 AM   #20
duceducenine
Registered User
 
duceducenine's Avatar
 
Join Date: Nov 2006
Location: el sobrante CA 94803
Posts: 284
Re: Stepped control arms

maybe i'll do a set and see how they work out let you know.....
duceducenine is offline   Reply With Quote
Old 03-31-2009, 03:19 PM   #21
chevy_mike
Never Ending Projects
 
chevy_mike's Avatar
 
Join Date: Jul 2006
Location: San Diego, CA
Posts: 3,836
Re: Stepped control arms

I had bought a set of dropped A arms from So Low way back in the day (before dropped spindles in '67-'72 year trucks). I think they were 2" drop and worked fine.

The only issue I had was without any bump stops, I came thru a dip to fast and bottomed the arms out. This caused the upper arms to over rotate the ball joint and killed one of my new upper ball joints.

Make sure you put some type of bump stop to keep from bottoming the lower arm.
__________________
.
1965 C10 Panel, Tiki Express http://www.67-72chevytrucks.com/vboa...d.php?t=506580 SOLD
1968 Chevy C10, Long, Fleetside, Hot Rod Hauler http://67-72chevytrucks.com/vboard/s...d.php?t=313233 SOLD
1965 Chevy C10, Long, Fleetside, Hot Rod C10 http://67-72chevytrucks.com/vboard/s...d.php?t=415702 SOLD


We were given two ears and one mouth for a reason... listen twice as much and speak half as often...
chevy_mike is offline   Reply With Quote
Old 04-08-2009, 06:07 AM   #22
Hottrucks
Redefining LowBudget
 
Hottrucks's Avatar
 
Join Date: Mar 2009
Location: lebanon Cow Hampshire
Posts: 4,538
Re: Stepped control arms

thats exactly what I'm taking about!!!!

How did it work out??????
__________________
1970 C10 CST fleetside 472 ....big dreams little cash...
SunShine Syndicate..

Mikes Sandwich Fair Run OCT 8th 2011
Hottrucks is offline   Reply With Quote
Old 04-08-2009, 11:41 AM   #23
woodwright
Enjoying left field
 
woodwright's Avatar
 
Join Date: Jun 2008
Location: Dillon Montana
Posts: 900
Re: Stepped control arms

Quote:
Originally Posted by Hottrucks View Post
thats exactly what I'm taking about!!!!

How did it work out??????
It worked good. At ride height, my LCA's are parralel to the ground. As far as having to shim the UCA's out, I don't think you would need to shim them out much. I could be wrong though. Look through my build thread.
__________________
Clint

70 Chevy 4WD "Ultimate Work Truck" SOLD
woodwright is offline   Reply With Quote
Old 04-08-2009, 06:22 PM   #24
Hottrucks
Redefining LowBudget
 
Hottrucks's Avatar
 
Join Date: Mar 2009
Location: lebanon Cow Hampshire
Posts: 4,538
Re: Stepped control arms

thanx I will look into it I think it makes sence to make a quick cut and weld the hard part is figuring out how much??
__________________
1970 C10 CST fleetside 472 ....big dreams little cash...
SunShine Syndicate..

Mikes Sandwich Fair Run OCT 8th 2011
Hottrucks is offline   Reply With Quote
Old 05-05-2009, 08:31 PM   #25
Hottrucks
Redefining LowBudget
 
Hottrucks's Avatar
 
Join Date: Mar 2009
Location: lebanon Cow Hampshire
Posts: 4,538
Re: Stepped control arms

ok guys looking for some insight?? I bagged the front of my truck with less than desireable results (not low enough) so it looks like back to the cutting and welding I think I will start with stepping the the lower A arm..so heres the question how much (15" wheels) I was thinking 1 1/2" I want to make it so there is some adjustment in my camber so should I take some out ( how much??) of the lower control arm...I also plan on making the cut in the top to elimnate some of the ball joint bind....and.... If that doesn't get it low enough I want to build in the lower cup for the air bag ( but I want to check scrubline with the stepped arms first)

Help outI would like to do this in one pass if I can

thanx
Jeff
__________________
1970 C10 CST fleetside 472 ....big dreams little cash...
SunShine Syndicate..

Mikes Sandwich Fair Run OCT 8th 2011
Hottrucks is offline   Reply With Quote
Reply

Bookmarks

Tags
arm, drop, lca, step, stepped


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:46 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com