|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
10-07-2007, 11:32 PM
|
#1 |
|
Roadtrip!
 
Join Date: Feb 2003
Location: Grand Rapids MN
Posts: 13,764
|
Looking for frame parts
Looking for the rear frame rails (both sides) for a 69 short 4x4. About the last 12" or so. I am not sure if the 2wd coil spring trucks share the same rails or not. Shipping would be to 55744. Thanks
__________________
67 gmc custom lwb dakota truck. Sold...And bought back 69 swb 4x4 project (in progress) 70 c-10 lwb texas truck 70 4x4/BB/bkts/posi/tach(retired) 70 swb (wifes) 70 jimmy camper 71 K-5 factory 2wd 71 cheyenne 4x4/tach/posi/ plow rig 71 Cheyenne20 BB, buckets, tach, tilt, 4 speed 72 jimmy CST wyoming rig 72 jimmy Colorado rig 72 lifted texas 4x4 3/4 ton burb 65 fury conv. 383/auto 65 chrysler 300 "L" 413 auto |
|
|
|
10-07-2007, 11:35 PM
|
#2 |
|
Registered User
Join Date: Mar 2006
Location: USA
Posts: 21,020
|
Re: Looking for frame parts
I think the 2wd rear frame parts should work.Are you needing past the rear crossmember? It's been a few years since I've had a 2wd 67-72 but I think the frame is the same past the last crossmember up a few feet till you get near the axle.The holes for the spring hangers will have to be drilled though.
Last edited by 1969k10stepside; 10-07-2007 at 11:35 PM. |
|
|
|
|
10-08-2007, 12:14 PM
|
#3 |
|
Senior Member
Join Date: Mar 2004
Location: Morrison, IL
Posts: 793
|
Re: Looking for frame parts
They are the same. I'm using the back section of frame on my 67 SWB 4x4. The PO had a flat bed on it and welded some other stuff to it. What a mess. I'm replacing a little in front of the last crossmember so i get it also. I don't want to bolt a new one in. Jason
__________________
2007 Chevy 2500HD crew cab, 4x4, duramax w/Allison trans. 2001 Chevy ZR2 Ext. cab 4x4 (DD) 1967 Chevy SWB 4x4, BBC, Th400, NP205, 6" lift, and 35's (In Process) 1970 Chevy Blazer 4x4, BBC, TH400, NP241, 6" lift, and 38.5 boggers in front, 44 boggers on the rear ( mud racer project) |
|
|
|
|
10-08-2007, 03:18 PM
|
#4 |
|
Roadtrip!
Join Date: Feb 2003
Location: Grand Rapids MN
Posts: 13,764
|
Re: Looking for frame parts
Thanks for the info. Anyone cutting up a frame that is fairly clean towards the back?
4bynut, i have a similar situation, but with some rust thrown in for good measure!! You should have seen the channel iron bumper that was on this thing. Eric
__________________
67 gmc custom lwb dakota truck. Sold...And bought back 69 swb 4x4 project (in progress) 70 c-10 lwb texas truck 70 4x4/BB/bkts/posi/tach(retired) 70 swb (wifes) 70 jimmy camper 71 K-5 factory 2wd 71 cheyenne 4x4/tach/posi/ plow rig 71 Cheyenne20 BB, buckets, tach, tilt, 4 speed 72 jimmy CST wyoming rig 72 jimmy Colorado rig 72 lifted texas 4x4 3/4 ton burb 65 fury conv. 383/auto 65 chrysler 300 "L" 413 auto |
|
|
|
|
10-08-2007, 06:24 PM
|
#5 |
|
Registered User
Join Date: May 2007
Location: Deale Md
Posts: 4,663
|
Re: Looking for frame parts
I have a 72 4x4 blazer frame for sale but i don't if its the same or not, maybe some one chime in with the answer.
__________________
James 63 GMC V6 4speed carryall 65 chevy swb bbw V8 auto 68 K20 327/4 speed, buddy buckets 2002 GMC CC Dually Duramax 64 GMC lwb 3/4 V6 4speed SOLD 66 GMC swb bbw buddy buckets SOLD IG duallyjams The only thing that stays the same is constant change! |
|
|
|
|
10-09-2007, 09:22 PM
|
#6 |
|
Roadtrip!
Join Date: Feb 2003
Location: Grand Rapids MN
Posts: 13,764
|
Re: Looking for frame parts
Still looking...
__________________
67 gmc custom lwb dakota truck. Sold...And bought back 69 swb 4x4 project (in progress) 70 c-10 lwb texas truck 70 4x4/BB/bkts/posi/tach(retired) 70 swb (wifes) 70 jimmy camper 71 K-5 factory 2wd 71 cheyenne 4x4/tach/posi/ plow rig 71 Cheyenne20 BB, buckets, tach, tilt, 4 speed 72 jimmy CST wyoming rig 72 jimmy Colorado rig 72 lifted texas 4x4 3/4 ton burb 65 fury conv. 383/auto 65 chrysler 300 "L" 413 auto |
|
|
|
|
| Bookmarks |
|
|
Hybrid Mode
