![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Mar 2013
Location: Grand Island, Ne.
Posts: 1,110
|
Floor pan repair Help plz?
Sup guys, Im gonna make my own floor pans to repair the rust. Im wondering what gauge steel I should use, 16, 18, or 22? and if I use 22 will it be strong enough for patches? This will be my first body repairs I have ever done, but I have been welding for years on all types of metal so thickness is not a problem in that dept. An I have no problem make more support bracing if need be.
Thanks in advance guys.
__________________
J. Vess, 6'6", Gearhead, Welder, Fabricator, Nutcase 1955 Chevy Stepside "Dudley" My daily http://www.67-72chevytrucks.com/vboa...d.php?t=760288 1972 Chevy C10, Project "Chevro~Layed out" Nether Storm Build Thread http://67-72chevytrucks.com/vboard/s...23#post6007523 |
![]() |
![]() |
![]() |
#2 |
1969 Custom 30 wrecker
Join Date: Sep 2001
Location: Pottsville, Pa
Posts: 2,611
|
Re: Floor pan repair Help plz?
It would be about 19 gauge from the factory so use the 18 gauge. 22 is way too thin.
I think floor braces were thicker so I'd use 16 gauge on anything like those.
__________________
Bob 63 Impala 283/PG/3.36 (under restoration) 66 Impala 327/PG/3.36 66 Chevelle SS 409/M22/3.55 69 Chevelle 307/PG/3.08 (future restoration) 69 C10 short stepside 454/TH350/3.73 69 Custom 30 tow truck 350/4 spd/4.10 (resto done, CRUISIN TIME!) 71 Cheyenne 20 fleetside 350/4 spd/4.10 71 Chevelle 6/PG/3.08 72 Chevelle 454/M21/4.10 |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Jun 2011
Location: Osceola, Ia
Posts: 2,017
|
Re: Floor pan repair Help plz?
If your going to make your own, use an old hood. Plenty tough, and probably super cheap from the right person..
Posted via Mobile Device
__________________
Shawn 68 chevy K/20 05 chevy 3/4 4x4 71 short step-sold ![]() 71 chevy Beauville van My build. http://67-72chevytrucks.com/vboard/s...d.php?t=633039 |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Mar 2013
Location: Grand Island, Ne.
Posts: 1,110
|
Re: Floor pan repair Help plz?
cool thx. Hood may be my best bet. 18ga. is hard to find around here. No one carries it. I may just have to order some if I cant find a hood or an old fender.
__________________
J. Vess, 6'6", Gearhead, Welder, Fabricator, Nutcase 1955 Chevy Stepside "Dudley" My daily http://www.67-72chevytrucks.com/vboa...d.php?t=760288 1972 Chevy C10, Project "Chevro~Layed out" Nether Storm Build Thread http://67-72chevytrucks.com/vboard/s...23#post6007523 |
![]() |
![]() |
![]() |
#5 |
motor exploder
Join Date: Mar 2009
Location: Pittsburgh, PA
Posts: 2,346
|
Re: Floor pan repair Help plz?
I made a few patches for my floor & firewall when I did my cab and had to order a sheet of 18 gauge to do it. 18 seems like a good compromise, since I could work it into the shapes I needed, was strong enough and easy to MIG weld with .030" or .023" wire. Just my .02
__________________
Adam 1969 Chevy CST/10 stepside, DART Big M/TREMEC Magnum Extreme/3.73's w/Detroit Truetrac 1965 Chevy Bel Air Wagon (daily driver), 327/TH350,10 bolt w/3.08's 1961 Chevy Bel Air Sport Coupe, ZZ454/M21/9" rear w/3.50's & Detroit Truetrac 2005 GMC 1500 ccsb 2wd, 6.0L/4L65e/3.73 G80 2006 GMC 2500HD ccsb 4x4, DMax LBZ/Allison 6spd/4.56's w/Detroit TrueTrac ![]() ![]() Use the SEARCH function on this forum - it is your friend!! |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Mar 2013
Location: Grand Island, Ne.
Posts: 1,110
|
Re: Floor pan repair Help plz?
Thank you gentlemen.
__________________
J. Vess, 6'6", Gearhead, Welder, Fabricator, Nutcase 1955 Chevy Stepside "Dudley" My daily http://www.67-72chevytrucks.com/vboa...d.php?t=760288 1972 Chevy C10, Project "Chevro~Layed out" Nether Storm Build Thread http://67-72chevytrucks.com/vboard/s...23#post6007523 |
![]() |
![]() |
![]() |
Bookmarks |
|
|