Seat Belt Retractor Bolt - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Already Gone** · 09-24-2013, 09:23 PM

I was pumped as I just received my new seat belt retractor cover. I went out to the truck and thought I'll just unbolt the old retractor and change the cover and bolt it back in. I cant get at the bolt cause it is at the back on the retractor and the gas tank is in the way from the front or above. Any one have an idea about this, what tool to use?
Posted via Mobile Device

*Mister-B* · 09-24-2013, 09:58 PM

Quote:

Originally Posted by Already Gone

I was pumped as I just received my new seat belt retractor cover. I went out to the truck and thought I'll just unbolt the old retractor and change the cover and bolt it back in. I cant get at the bolt cause it is at the back on the retractor and the gas tank is in the way from the front or above. Any one have an idea about this, what tool to use?
Posted via Mobile Device

Hi Greg,

I think the whole assembly goes through the floor, and there's a nut under the truck. Undo the nut, pull the entire assembly out, and you can then easily work on it. I removed both of mine when I restored them, and that's what I did
Posted via Mobile Device

*Mister-B* · 09-24-2013, 10:01 PM

Wait a minute. This should be even easier than I thought. Just pull up and wiggle the old plastic retractor, and it'll pop off and then you can feed the belt through the new one and POP it on. You'll need to use a little force to wiggle the old one off, but it'll come. If you can warm it with a hair dryer or heat gun first, it'll be easier
Posted via Mobile Device

MikeyMan · 09-26-2013, 05:54 AM

I recall having trouble accessing that bolt too because of the gas tank.

I believe I used a short socket, universal, extension, then ratchet/breaker bar.

09-24-2013, 09:23 PM	#1
Already Gone 70+ ( Old Skool Club ) Join Date: Nov 2003 Location: Saskatoon, Saskatchewan ,Canada Posts: 9,143	Seat Belt Retractor Bolt I was pumped as I just received my new seat belt retractor cover. I went out to the truck and thought I'll just unbolt the old retractor and change the cover and bolt it back in. I cant get at the bolt cause it is at the back on the retractor and the gas tank is in the way from the front or above. Any one have an idea about this, what tool to use? Posted via Mobile Device __________________ 1972 C10 Custom/Deluxe 613 Highlander 406/700R4 1999 White Tahoe LS 4x2 with Z56 Police Package 1992 K1500 GMC Suburban Members I have personally met: MusicMan70 - HeavyD - ChewyChevy67 - StingRay -71SWB4x4 - 67 Burb - DeadheadNM - too much stuff - bc65 - das601 " Circumsatances Do Not Change Responsibility " " The Sky is not the Limit, Your Mind is." Marilyn Monroe .. RIP Charlie Watts 1941 - 2021

09-24-2013, 10:01 PM	#3
Mister-B Account Suspended Join Date: Oct 2012 Location: Salt Lake City, Utah Posts: 3,331	Re: Seat Belt Retractor Bolt Wait a minute. This should be even easier than I thought. Just pull up and wiggle the old plastic retractor, and it'll pop off and then you can feed the belt through the new one and POP it on. You'll need to use a little force to wiggle the old one off, but it'll come. If you can warm it with a hair dryer or heat gun first, it'll be easier Posted via Mobile Device

09-26-2013, 05:54 AM	#4
MikeyMan Registered User Join Date: May 2008 Location: S.W. Chicago, IL. Posts: 317	Re: Seat Belt Retractor Bolt I recall having trouble accessing that bolt too because of the gas tank. I believe I used a short socket, universal, extension, then ratchet/breaker bar.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.