Wire loom question on installation

[Peanut74]

Got my cab all painted up and ready for the next step. But I am not sure if I should run the main wire loom first or put the major components (wiper motor, a/c, dash speaker, etc). This is my first time doing a major rewiring and just wanted to get some experienced feedback.
Thanks

[03BlkZ]

Originally Posted by Peanut74

Got my cab all painted up and ready for the next step. But I am not sure if I should run the main wire loom first or put the major components (wiper motor, a/c, dash speaker, etc). This is my first time doing a major rewiring and just wanted to get some experienced feedback.
Thanks

In about 2 weeks time I will be in the exact position you are in. I plan to run my wiring first before installing any major interior components. Obviously it will help to have things like the ignition switch and maybe the heater box installed as well as speaker and wiper motor. Then you can route the wires however you need.

[Peanut74]

That is the way I am leaning. Basically work from the bottom of the dash out. IE install the wiper motor, heater and a/c box and speaker first. Then install the wire loom followed by the switches and such. Lastly the interior components.

[Lee H]

I ran the harness and taped the ends near where the component was to be installed. Then I installed the component and terminated the harness. Seemed to work OK.

[un4gvn!]

Install the dash pad first. You'll thank me in the morning.

[Peanut74]

Good point un4. It would truly be a PITA to it in after everything else. But on the other hand I've had to take everything else multiple times why should the dash be any different.

[Peanut74]

Well I have graduated to working on the interior. Currently working on seats and the speaker box behind the seat. I did test fit the dash pad and like many others found that I needed to slot the holes some to get it to the right position on the front of the dash. Going to reinstall it tomorrow for the final time as I have already install the wiper motor. I also want to install the dash speaker with the speaker wires preinstalled. Once that is all installed I will have a better idea on how to run the wire loom.

[03BlkZ]

Originally Posted by Peanut74

Well I have graduated to working on the interior. Currently working on seats and the speaker box behind the seat. I did test fit the dash pad and like many others found that I needed to slot the holes some to get it to the right position on the front of the dash. Going to reinstall it tomorrow for the final time as I have already install the wiper motor. I also want to install the dash speaker with the speaker wires preinstalled. Once that is all installed I will have a better idea on how to run the wire loom.

I'm already done. I started with the dash kit then moved to the rear lights kit. I installed some components as I went. Then did the front light kit followed by the engine and did the starter/battery wiring last. I routed everything how I wanted it then put the harnesses in loom. I hooked the battery up last weekend and had a minor horn issue but that's it. Started the truck yesterday and everything seems to be functioning great.

[Getter-Done]

Originally Posted by Peanut74

Well I have graduated to working on the interior. Currently working on seats and the speaker box behind the seat. I did test fit the dash pad and like many others found that I needed to slot the holes some to get it to the right position on the front of the dash. Going to reinstall it tomorrow for the final time as I have already install the wiper motor. I also want to install the dash speaker with the speaker wires preinstalled. Once that is all installed I will have a better idea on how to run the wire loom.

Peanut74
Sounds like you have a good plan.
Are you making your own wiring harness or adding to a purchased harness?

.







.

[Peanut74]

Well I decided to run the loom on the top of the fresh air duct. Once I have my Vintage ac system I will know if I choose wisely

[Getter-Done]

That is looking Good

Attention to details pays off.











.

[BigBird05]

My experience with those press on wiring retainers is they don't last as long as you would like them to. Find a screw hole that you can use for a metal retainer.

[A1971Blazer]

Originally Posted by BigBird05

My experience with those press on wiring retainers is they don't last as long as you would like them to. Find a screw hole that you can use for a metal retainer.

They also have the powerful little magnets that have a loop in them for a zip tie
I have a few of them..they are really strong and you can move them if necessary

[fun in dirt]

Originally Posted by A1971Blazer

They also have the powerful little magnets that have a loop in them for a zip tie
I have a few of them..they are really strong and you can move them if necessary

Oooo this sounds like a good little thing to have! I have never seen such ..Where do you buy them?

[A1971Blazer]

Originally Posted by fun in dirt

Oooo this sounds like a good little thing to have! I have never seen such ..Where do you buy them?

I tried to post a link....not sure what happened
Amazon has them, Speedway motors, and I'm sure there are more
Google "zip tie magnetic base"
these thing work great

[Peanut74]

Never seen magnet zip tie bases before. Would have made running the wire loom a lot easier.

I did install the sound dealer first. I am very glad I put the dash pad in before the a/c. The center dash pad nut was hard enough to get on with basically nothing in the way.

[Peanut74]

Thanks Getter Done. To bad right after I took the pics I noticed that I forgot to put the washer pump wire in the loom. Had to open it up for about the hunderth time to put it in.

Big Bird I agree that the wire retainer sticky pads don't hold. The fix is put epoxy on the back side then stick it on. Son in-law worked at ARP and that is what they did on their race cars. Haven't had one come off since I started doing it that wY.

[Peanut74]

Well I have made a lot of progress on the dash. The order I have done it is wire harness first, wiper motor, center speaker, dash pad and then the Vintage air system. I still need to put the drivers side together put it seems to be coming together. I think the next big hurdle will be to run the heater and A/C duct work.

[Accelo]

The dash pad is very important to get in first.
You will not be able to get to all the pad retaining nuts installed if the radio is in. And the main harness wiring runs directly under the retaining nuts.
Don't forget the firewall insulation. I would put that in second as a lot of the wiring and hoses go through it. Including the throttle cable if you are using one. The Vintage air glove box is also difficult to get in with the radio in place.
American Auto Wire harness was plenty long for the passenger door. But I wouldn't recommend it for a stock truck. Lots of work getting it installed as you have to make up at last one end of the wire.