![]() |
![]() |
#1 |
Registered User
Join Date: Feb 2000
Location: Edmonton, Alberta, Canada
Posts: 599
|
![]()
I'm finnally getting close to finishing my 5 speed swap and I'm wanting to go to a one piece driveshaft, from the very best of my measurments I need a driveshaft 67" long from the end of the yokes. (longest dist) What have other people taken a one piece out of? I'd sure like to find one I don't have to cut, I have a bit of room to play because my slip yoke has quite a bit of travel, it could be maybe a 1/2" longer or 1" shorter and still work. Any ideas? or if I have to cut and weld I've heard on here about putting some oil inside the driveshaft to get a fluid balance. any insight on this? Thanks!
Jesse ------------------ Near Saskatoon, Saskatchewan, Canada. 67 c-10, Long fleet, Newly swapped front disks, 5 lug rear end, 327 v-8 with Vortech heads, edlbrock performer rpm air gap manifold, 1406 carb and comp XE 256 cam. Backed by a getrag 5 speed and 1 piece driveshaft. Finnally running, almost driving! www.geocities.com/chevy67jesse
__________________
Edmonton, Alberta, 67 c-10, Long fleet, front disks, 5 lug rear end, 327 with Vortechs, edlbrock manifold, comp cams XE 256, 600cfm carb. Backed by a getrag 5 speed and 1 piece driveshaft. 1993 Dihatsu Hijet Jumbo cab 4x4, currently converting to battery electric power. |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Aug 2001
Location: rock island,il,usa
Posts: 5,382
|
![]()
Cut& balance is only about $70 in my area,IMO good money spent. From what I understand,you should run a 4" dia shaft when going to a 1 pc in the 5 1/2-6 ft range on lenght(it can stepdown on the ends). To set up & measure lenght,you need to slide the slip yolk all the way the trans,mark it,then pull it out 3/4"-1",then measure C to C on the caps.Good luck.......69 longhorn.
__________________
http://community.webshots.com/user/hotrodhorn |
![]() |
![]() |
![]() |
#3 |
Registered User
![]() Join Date: Feb 2000
Location: Georgetown, KY, USA
Posts: 631
|
![]()
Jesse,
You might look at large GM cars for your drive shaft. I have one from a 86 Caprice Wagon that I'm going to have shortened for my SWB and 700r4. I don't know the exact length of it, but it is close to what you need. ------------------ Woody '69 Custom-10 Deluxe Short Fleetside,Factory 350cid/TH400,A/C,PS,PB,Carpet Coming soon 700R4, 350 Crate Engine, Pwr Disks... |
![]() |
![]() |
![]() |
#4 |
Account Suspended
Join Date: May 2000
Location: IL
Posts: 0
|
![]()
yeah look under full size rwd cars, lots of them are in the 60's" for lengths, i have a stash of shafts from cars and such, they are all right around that length
good luck ------------------ Randy- Lincoln, IL randy@ccaonline.com 2177353230 *many GM parts bought, traded, or sold -am parting out: '81 Cutlass Supreme Brougham current fleet: -71 C-10 350/CH465/3.07- basketcase, #1 -90 Cavalier 2.2L sky blue, a driver -84 Z28 5.0L/700R4/3.73 daily driver -84 Firebird/SE 2.8L/T-5/3.73/engine bad, project #2 -82 purple Trans Am, project #3 *Paint is overrated* © RSS Enterprises 2000 |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Feb 2000
Location: Edmonton, Alberta, Canada
Posts: 599
|
![]()
I went to the local yard today and I actually found a driveshaft the exact length, 66 3/4" ! I'm still amazed at my luck! I put it in, rolled it down a hill with the motor running, popped it in gear, drove it around for the first time in almost a year, with no clutch control, or brakes! I still need the hyd clutch hose and brake lines. Wasn't very practical but it was fun, and loud! Finnaly!
Thanks for the help Jesse ------------------ Near Saskatoon, Saskatchewan, Canada. 67 c-10, Long fleet, Newly swapped front disks, 5 lug rear end, 327 v-8 with Vortech heads, edlbrock performer rpm air gap manifold, 1406 carb and comp XE 256 cam. Backed by a getrag 5 speed and 1 piece driveshaft. Finnally running, almost driving! www.geocities.com/chevy67jesse
__________________
Edmonton, Alberta, 67 c-10, Long fleet, front disks, 5 lug rear end, 327 with Vortechs, edlbrock manifold, comp cams XE 256, 600cfm carb. Backed by a getrag 5 speed and 1 piece driveshaft. 1993 Dihatsu Hijet Jumbo cab 4x4, currently converting to battery electric power. |
![]() |
![]() |
![]() |
#6 |
Account Suspended
Join Date: May 2000
Location: IL
Posts: 0
|
![]()
are lucky then !
make sure isnt shoved too far up into the back of the tranny |
![]() |
![]() |
![]() |
#7 |
Slowly getting CRSS...
Join Date: Jul 2001
Location: Lutz, Florida
Posts: 656
|
![]()
that vehicle did you end up pulling the axle out of?
------------------ Lutz, Fl My Team Website The Heavy Chevy Website ------------------
__________________
-Nic Lutz, Fl My Team Website The Heavy Chevy Website ------------------
There is No replacement for Displacement... "If everything seems under control, you're just not going fast enough." - Mario Andretti |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Feb 2000
Location: Edmonton, Alberta, Canada
Posts: 599
|
![]()
The axle is off a 72 chev, I don't know what the shaft is off of and the tranny's from a 90 chev 1/2t. Thanks for the help!
Jesse ------------------ Near Saskatoon, Saskatchewan, Canada. 67 c-10, Long fleet, Newly swapped front disks, 5 lug rear end, 327 v-8 with Vortech heads, edlbrock performer rpm air gap manifold, 1406 carb and comp XE 256 cam. Backed by a getrag 5 speed and 1 piece driveshaft. Finnally running, almost driving! www.geocities.com/chevy67jesse
__________________
Edmonton, Alberta, 67 c-10, Long fleet, front disks, 5 lug rear end, 327 with Vortechs, edlbrock manifold, comp cams XE 256, 600cfm carb. Backed by a getrag 5 speed and 1 piece driveshaft. 1993 Dihatsu Hijet Jumbo cab 4x4, currently converting to battery electric power. |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|