![]() |
![]() |
#476 |
Damn Yankee
Join Date: Feb 2007
Location: Lynchburg, VA
Posts: 2,261
|
Re: PO has me PO'd
|
![]() |
![]() |
![]() |
#477 | |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,504
|
Re: PO has me PO'd
Thanks Tim
Quote:
Skill level 0-10, 10 being the hardest, about a 5. I have more problems with a and b posts lower patch panels. If the PO hasn't made any patches it's alot easier. When ya get into a factory spot weld it's alot easier. If ya can take a spot weld apart without destroying the metal your trying to save, you can do this, and that is easiest if you make the pc. your trying to remove flat( cut away all metal till you have a ribbon of metal with the spot weld in it), then just use the 4 1/2" grinder to remove the spot weld, then move on to the next one, prying up slightly I spent about a week and a half cutting out the old floorboard, plasma woulda helped. You can reinstall floorboard with plug welds, so you don't really have to know how the weld, if ya can fill in holes with a mig. You're dealing with a factory seam, front and rear, so it makes it easy to line up flanges (before I started, I painted the seam area, so it showed a line to match up) should also be less welding then a floor patch, if you consider total distance tobe welded Yes, depending on his ability ![]()
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; 04-18-2008 at 01:48 PM. |
|
![]() |
![]() |
![]() |
#478 |
Registered User
Join Date: Oct 2003
Location: Central Vermont
Posts: 8,538
|
Re: PO has me PO'd
Makes sense due to the nature of the beast, I was just curious.
Will this cab be dipped or sprayed for the initial primer? If you pry open the seam on the bottom of the cowl, between the spot welds, it will help drain better. ![]() The stock weep holes typically gets clogged up, that's when the problems start. Last edited by vtblazer; 04-18-2008 at 01:52 PM. |
![]() |
![]() |
![]() |
#479 |
Can't wait to retire!!
Join Date: Feb 2003
Location: Corunna, MI
Posts: 1,575
|
Re: PO has me PO'd
I can see it now...Jon sells the part and offers to fly Jim to the customer's site (of course on the customer's dime) for the install. This would be great, but where do I fit in? Ah yes, Jim, you'll need an agent! And Kurt, hmm, well we'll have to have a west coast installer as well as an east coast installer! I think this is a great idea.
![]() ![]() ![]()
__________________
![]() 2009 4x4 Chevy Crew Cab 6.0 1989 4x4 Siverado (270,000 miles) 1972 4x4 Blazer 2007 Chevy Cutaway 1 ton 1970 Corvette (sons project) RIP - CLR 10/11/09 |
![]() |
![]() |
![]() |
#480 | |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,504
|
Re: PO has me PO'd
Quote:
![]()
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
|
![]() |
![]() |
![]() |
#481 |
Can't wait to retire!!
Join Date: Feb 2003
Location: Corunna, MI
Posts: 1,575
|
Re: PO has me PO'd
Maybe I can convert the percentage to beer...hmm.
![]()
__________________
![]() 2009 4x4 Chevy Crew Cab 6.0 1989 4x4 Siverado (270,000 miles) 1972 4x4 Blazer 2007 Chevy Cutaway 1 ton 1970 Corvette (sons project) RIP - CLR 10/11/09 Last edited by Chevyman63; 04-18-2008 at 02:42 PM. |
![]() |
![]() |
![]() |
#482 | |
Damn Yankee
Join Date: Feb 2007
Location: Lynchburg, VA
Posts: 2,261
|
Re: PO has me PO'd
Quote:
PS: I get 8% of Jim's take |
|
![]() |
![]() |
![]() |
#483 |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,504
|
Re: PO has me PO'd
Dude, I can see the three of us working for beer money, our shop would have to be on a beach somewhere
![]()
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; 04-18-2008 at 03:09 PM. |
![]() |
![]() |
![]() |
#484 | |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,504
|
Re: PO has me PO'd
Quote:
![]() ![]() I can't talk anymore, I'm supposed to be up in the middle of NJ
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; 04-18-2008 at 03:11 PM. |
|
![]() |
![]() |
![]() |
#485 | |
Can't wait to retire!!
Join Date: Feb 2003
Location: Corunna, MI
Posts: 1,575
|
Re: PO has me PO'd
Quote:
![]() I've got to go to work too.
__________________
![]() 2009 4x4 Chevy Crew Cab 6.0 1989 4x4 Siverado (270,000 miles) 1972 4x4 Blazer 2007 Chevy Cutaway 1 ton 1970 Corvette (sons project) RIP - CLR 10/11/09 |
|
![]() |
![]() |
![]() |
#486 |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,504
|
Re: PO has me PO'd
If I sit here much longer the Boss is going to yell! We'll work on that 8% thing. Shop on the beach
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
![]() |
![]() |
![]() |
#487 |
Damn Yankee
Join Date: Feb 2007
Location: Lynchburg, VA
Posts: 2,261
|
Re: PO has me PO'd
I homebrew so there's no shortage of motivation at my house
|
![]() |
![]() |
![]() |
#488 |
Post Whore
![]() Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,684
|
Re: PO has me PO'd
That complete floor repo just blows my mind!
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
![]() |
![]() |
![]() |
#489 |
Registered User
Join Date: May 2006
Location: San Antonio, Texas
Posts: 372
|
Re: PO has me PO'd
i just need someone to do this on a blazer so i can see how to do it what with bracing and all.
__________________
'72 K5 CST Blazer 4x4 in perpetual progress '96 2dr Tahoe 4x4 daily driver, Black Bear Performance tune, 285-75-16 Nitto Grapplers, Magnaflow muffler, K&N Air filter, Bilstein Shocks.........E-fan, DT Tri Y or Pacesetter LTs coming soon |
![]() |
![]() |
![]() |
#490 | |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,504
|
Re: PO has me PO'd
Quote:
I say take the front clip off, cut the floor strait across. You may not need to raise the bed, since the floor pan mounts to the step up. Clean up the factory seam(front and rear). You will have to modify the rear of the floorpan some. Put the cowl/windshield back on zip screw both ends and check door alignment. If they line up, mount your rockers. I think bracing would be in your way, but that's just me. This floor pan is extremely strong. I have about 20 zip screws holding it together up to this point
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; 04-19-2008 at 01:08 AM. |
|
![]() |
![]() |
![]() |
#491 |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,504
|
Re: PO has me PO'd
I was working on removing the cowl area today, so I thought I'd post up some pics of spot weld removal
![]() ![]() This is the area of making a ribbon of the sheet metal, cutting the top and bottom so your left with a 1" pc. with the spot weld in the middle ![]() ![]() ![]()
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
![]() |
![]() |
![]() |
#492 |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,504
|
Re: PO has me PO'd
![]() ![]() ![]() ![]()
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
![]() |
![]() |
![]() |
#494 |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,504
|
Re: PO has me PO'd
Thank you,but you outwork me hands down. Nice progress on your truck. I haven't dun anything to mine in 3 weeks
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
![]() |
![]() |
![]() |
#495 |
Can't wait to retire!!
Join Date: Feb 2003
Location: Corunna, MI
Posts: 1,575
|
Re: PO has me PO'd
I couldn't agree more...nice work Jim.
__________________
![]() 2009 4x4 Chevy Crew Cab 6.0 1989 4x4 Siverado (270,000 miles) 1972 4x4 Blazer 2007 Chevy Cutaway 1 ton 1970 Corvette (sons project) RIP - CLR 10/11/09 |
![]() |
![]() |
![]() |
#496 |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,504
|
Re: PO has me PO'd
I think the props should go to Tri-Pro Automotive for making this piece available to us...
Thanks Tim
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; 04-19-2008 at 05:43 AM. |
![]() |
![]() |
![]() |
#497 |
Registered User
Join Date: Oct 2003
Location: Central Vermont
Posts: 8,538
|
Re: PO has me PO'd
Why the need to remove the firewall piece?
Rust reason's or are you installing a shaved/different part? Cool work J. ![]() |
![]() |
![]() |
![]() |
#498 |
Damn Yankee
Join Date: Feb 2007
Location: Lynchburg, VA
Posts: 2,261
|
Re: PO has me PO'd
Kurt- there are rust holes in it; just hard to see in the pictures. Most of the holes are down low near the mating flange for the floor. It's apart, we have the new firewall so we figured why not replace it and know we don't have any issue with rust to deal with.
|
![]() |
![]() |
![]() |
#499 | |
Registered User
Join Date: Oct 2003
Location: Central Vermont
Posts: 8,538
|
Re: PO has me PO'd
Quote:
![]() I'm bringing home another blazer today...wanna try the floor in the real deal? ![]() Edit: Got the body mount on Tuesday, thanks. Last edited by vtblazer; 04-19-2008 at 01:48 PM. |
|
![]() |
![]() |
![]() |
#500 |
Damn Yankee
Join Date: Feb 2007
Location: Lynchburg, VA
Posts: 2,261
|
Re: PO has me PO'd
I'll talk to Doug about selling you one at wholesale if you'll document what you do to install it
|
![]() |
![]() |
![]() |
Bookmarks |
|
|