67-72 Gauge Panel Removal - The 1947 - Present Chevrolet & GMC Truck Message Board Network

krue · 07-15-2005, 07:57 PM

As promised here is a How-to on removing gauge panels. Principles should be the same regardless of style of dash you have.

1. First step is to unhook the battery (to keep from draining it with the lights on, unless you can remember to turn them back off).

2. Next remove the windshied wiper knob by loosening the screw holding it on.

krue · 07-15-2005, 08:03 PM

3. Remove headlight switch by pulling knob out (basically turning headlights on)
then reach up under the dash and press the button on top of the switch and pull the knob the rest of the way out.

4. Remove the bezel rings from the wiper and headlight switches.

krue · 07-15-2005, 08:07 PM

5. While you are under the dash, disconnect the speedo cable (you can almost make it out in the first pic.

6. Disconnect the oil pressure line (if so equipped), unplug the wiring harness from the gauge panel. You may also want to remove the bulbs from the top of the panel (turn signal indicator lights) to make it a little easier to remove the panel.

krue · 07-15-2005, 08:11 PM

7. To make it a lot easier to remove, were gonna drop the steering column a little. First remove the Phillip screws holding the rubber boot retainer (1 in pic).
Then remove the 4 bolts holding the plate underneath (2 in pic).

8. Loosen the bolts clamping the steering column in place. It's not necessary to totally remove them.

krue · 07-15-2005, 08:15 PM

9. Finally, remove the screws holding the panel in place. Lean the top of the panel toward you, remove turn signal bulbs (if not already done) and pull the optic fiber loose if you have auto column (it's on the inner side of the back of the speedo). Finish pulling the panel out.

10. Installation is the reverse of removal.

Jakes-66-K10 · 07-21-2005, 09:28 AM

How about for trucks equipped with a choke cable? Can't figure out how that comes out

krue · 07-21-2005, 10:07 AM

I've never seen one with a choke cable, so I don't know. I'm sure someone will chime in.

chevykid04 · 08-03-2005, 02:44 PM

does the bezel for the the headlight switch just pop off?

panhandler62 · 08-04-2005, 09:07 AM

The bezels for the headlight, wipers and choke (if equipped) are spun on. If they are too tight to remove by hand they do have two holes that you can poke the points of a pair of needle-nose pliars into to facilitate removal.

**BOSS** · 08-21-2005, 02:47 PM

When i took out one with a choke it just unscrewed like the bezels do.

07-15-2005, 07:57 PM	#1
krue Designated A-hole! Join Date: Mar 2003 Location: South Mississippi Posts: 36,448	67-72 Gauge Panel Removal As promised here is a How-to on removing gauge panels. Principles should be the same regardless of style of dash you have. 1. First step is to unhook the battery (to keep from draining it with the lights on, unless you can remember to turn them back off). 2. Next remove the windshied wiper knob by loosening the screw holding it on. Attached Images __________________ "If it ain't broke, fix it 'til it is!" Being stupid ain't illegal. We're Still Debt Free Except for the House!!! www.daveramsey.com 70 GMC SWB Stepside project "Green Booger" soon to be 6.0l/4l80e 93 S-10 "Poppaw's Truck"

07-15-2005, 08:03 PM	#2
krue Designated A-hole! Join Date: Mar 2003 Location: South Mississippi Posts: 36,448	3. Remove headlight switch by pulling knob out (basically turning headlights on) then reach up under the dash and press the button on top of the switch and pull the knob the rest of the way out. 4. Remove the bezel rings from the wiper and headlight switches. Attached Images __________________ "If it ain't broke, fix it 'til it is!" Being stupid ain't illegal. We're Still Debt Free Except for the House!!! www.daveramsey.com 70 GMC SWB Stepside project "Green Booger" soon to be 6.0l/4l80e 93 S-10 "Poppaw's Truck"

07-15-2005, 08:07 PM	#3
krue Designated A-hole! Join Date: Mar 2003 Location: South Mississippi Posts: 36,448	5. While you are under the dash, disconnect the speedo cable (you can almost make it out in the first pic. 6. Disconnect the oil pressure line (if so equipped), unplug the wiring harness from the gauge panel. You may also want to remove the bulbs from the top of the panel (turn signal indicator lights) to make it a little easier to remove the panel. Attached Images __________________ "If it ain't broke, fix it 'til it is!" Being stupid ain't illegal. We're Still Debt Free Except for the House!!! www.daveramsey.com 70 GMC SWB Stepside project "Green Booger" soon to be 6.0l/4l80e 93 S-10 "Poppaw's Truck"

07-15-2005, 08:11 PM	#4
krue Designated A-hole! Join Date: Mar 2003 Location: South Mississippi Posts: 36,448	7. To make it a lot easier to remove, were gonna drop the steering column a little. First remove the Phillip screws holding the rubber boot retainer (1 in pic). Then remove the 4 bolts holding the plate underneath (2 in pic). 8. Loosen the bolts clamping the steering column in place. It's not necessary to totally remove them. Attached Images __________________ "If it ain't broke, fix it 'til it is!" Being stupid ain't illegal. We're Still Debt Free Except for the House!!! www.daveramsey.com 70 GMC SWB Stepside project "Green Booger" soon to be 6.0l/4l80e 93 S-10 "Poppaw's Truck"

07-15-2005, 08:15 PM	#5
krue Designated A-hole! Join Date: Mar 2003 Location: South Mississippi Posts: 36,448	9. Finally, remove the screws holding the panel in place. Lean the top of the panel toward you, remove turn signal bulbs (if not already done) and pull the optic fiber loose if you have auto column (it's on the inner side of the back of the speedo). Finish pulling the panel out. 10. Installation is the reverse of removal. Attached Images __________________ "If it ain't broke, fix it 'til it is!" Being stupid ain't illegal. We're Still Debt Free Except for the House!!! www.daveramsey.com 70 GMC SWB Stepside project "Green Booger" soon to be 6.0l/4l80e 93 S-10 "Poppaw's Truck"

07-21-2005, 09:28 AM	#6
Jakes-66-K10 Registered User Join Date: Aug 2004 Location: Idaho Posts: 640	How about for trucks equipped with a choke cable? Can't figure out how that comes out

07-21-2005, 10:07 AM	#7
krue Designated A-hole! Join Date: Mar 2003 Location: South Mississippi Posts: 36,448	I've never seen one with a choke cable, so I don't know. I'm sure someone will chime in. __________________ "If it ain't broke, fix it 'til it is!" Being stupid ain't illegal. We're Still Debt Free Except for the House!!! www.daveramsey.com 70 GMC SWB Stepside project "Green Booger" soon to be 6.0l/4l80e 93 S-10 "Poppaw's Truck"

08-03-2005, 02:44 PM	#8
chevykid04 4 speed, hurst shiftin Join Date: Jun 2002 Location: Hudson, Wi Posts: 405	does the bezel for the the headlight switch just pop off? __________________ Shane 1970 Chevy C10

08-04-2005, 09:07 AM	#9
panhandler62 Java Mechanic Join Date: Jun 2005 Location: Martinsburg, WV Posts: 6,763	The bezels for the headlight, wipers and choke (if equipped) are spun on. If they are too tight to remove by hand they do have two holes that you can poke the points of a pair of needle-nose pliars into to facilitate removal. __________________ Keith 11 Lincoln MKT -- Momma's wagon 13 G37xS -- middle age crazy car 68 C20 Fleetside -- RIP Decorating the whole town up at a cost of $27 ....

08-21-2005, 02:47 PM	#10
BOSS Just here to help Join Date: Jan 2002 Location: Norwood,Mo Posts: 3,890	When i took out one with a choke it just unscrewed like the bezels do. __________________ Support our site Norwood Survivor

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.