![]() |
![]() |
#1 |
Registered User
Join Date: May 2016
Location: Brewster
Posts: 18
|
Engine Stands
Can someone confirm left/right engine stands for a SBC. Attached is a pic as I think it should be. Does that look correct or is it reversed and should curve forward? Thanks.
|
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Mar 2013
Location: Houston, TX
Posts: 348
|
Re: Engine Stands
ecna, check out the thread about the frame pictures. There are many shots of the engine stands, probably answers your question.
http://67-72chevytrucks.com/vboard/s...d.php?t=700421 |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: May 2016
Location: Brewster
Posts: 18
|
Re: Engine Stands
I have literally spent hours reading engine mount threads. I also just went through the link you posted. There is one kinda decent shot but not enough from above to see the angle. With all the experience in this board, I thought identifying left from right would be an easy question. Thanks for the link though.
|
![]() |
![]() |
![]() |
#4 |
Senior Member
![]() Join Date: Jul 2015
Location: Warrenton VA
Posts: 1,053
|
Re: Engine Stands
I can look at mine this evening and get you a pic if needed.
__________________
71 c-10 Long Bed, under the knife for a No Limit Engineering Wide Ride Chassis Pack and coil over static drop. 07 Silverado Classic 2wd 95 Camaro 427SBC/TH350 |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: May 2016
Location: Brewster
Posts: 18
|
Re: Engine Stands
That would be great. Thank you.
Look at my pic, you can see the way I have it (and think it fits best) it turns towards the back of the truck. If I flip them, they turn towards the front of the truck. The holes in the frame have been welded closed as it had a different mount system installed previously, otherwise it might me much more clear. Obviously I want them correct before I drill holes. |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Oct 2012
Location: Green Valley Arizona
Posts: 1,351
|
Re: Engine Stands
They point towards the rear like you have it positioned.
__________________
1970 C10 Short Stepper with 71/72 front clip. |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Apr 2011
Location: Mustang, Oklahoma
Posts: 2,806
|
Re: Engine Stands
Looks correct to me. Here's mine.
__________________
Dan <---(my name) 67 SWB C10 project "GEORGIA"-59 Brookwood 2dr wag...Next project-03 Tahoe 4x4 5.3 family ride-07 Hondur Accord, commuter car |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: May 2016
Location: Brewster
Posts: 18
|
Re: Engine Stands
|
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: May 2016
Location: Brewster
Posts: 18
|
Re: Engine Stands
|
![]() |
![]() |
![]() |
#10 |
Senior Member
![]() Join Date: Jul 2015
Location: Warrenton VA
Posts: 1,053
|
Re: Engine Stands
Looks like you got what you needed, I got home later than expected last night and it was dark by the time I got out to the yard.
__________________
71 c-10 Long Bed, under the knife for a No Limit Engineering Wide Ride Chassis Pack and coil over static drop. 07 Silverado Classic 2wd 95 Camaro 427SBC/TH350 |
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: May 2016
Location: Brewster
Posts: 18
|
Re: Engine Stands
|
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|