|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
11-21-2004, 06:57 PM
|
#1 |
|
Senior Member
Join Date: Jun 2003
Location: Westminster, CO
Posts: 3,071
|
Original GM 71' Fenders For sale
I have two 71' fenders ( R / L) in Primer/Guide coat and Straight . The back side only has a small amount of surface rust. They trim holes have been welded up. They came with my 71'. They have been stored inside since coming off the truck. Primer was shot about 9 months ago. I'm looking for $75.00 a piece plus the ride. If you guys don't want they I will ebay them.
__________________
Alex 1971 Lil' Red 350 SBC 700R4 |
|
|
|
11-21-2004, 10:00 PM
|
#2 |
|
What was I thinking??
Join Date: Dec 2003
Location: Commerce City Co
Posts: 636
|
To bad I have to many thing going on right now or I would jump on those....
__________________
72 K5 that needs lots of parts.. 71 GMC 3/4 4x4 That doesn't need much which is a good thing I don't think I could aford another money pit... |
|
|
|
|
11-22-2004, 01:29 PM
|
#3 |
|
Registered User
Join Date: Dec 2003
Location: Gap-Pa.
Posts: 186
|
Interested
probably common knowledge, but are these interchangeable with a Chevy (same year) Any estimates on shipping to 92880 or 17527. Thanks.
__________________
71 k10 swb 72 k5 72 Burb 4x4 72 GMC Burb 4x4 |
|
|
|
|
11-22-2004, 02:33 PM
|
#4 | |
|
Too many is never enough!
Join Date: May 2003
Location: Idaho Falls, ID
Posts: 455
|
Quote:
How's the projects Alex?
__________________
Jason 1968 K10 SWB Fleetside 1971 K2500 GMC LWB 1968 K20 (later frame, donor body) 1972 C20 LWB parts truck 1993 K2500 Suburban, tow rig, 454, 4L80E NEW!! 18' Siem's car hauler 2004 Honda Odyssey (family man!) |
|
|
|
|
|
11-22-2004, 03:56 PM
|
#5 |
|
Not Mine But A beauty
Join Date: Aug 2004
Location: Southern CaL
Posts: 368
|
all those little holes either are rust or filler arent they?
__________________
68 Chevy Shortbed 454/400 2000 Chevrolet Camaro SS 6spd 2011 Silverado 5.3 6spd auto |
|
|
|
|
11-22-2004, 08:09 PM
|
#6 | |
|
Senior Member
Join Date: Jun 2003
Location: Westminster, CO
Posts: 3,071
|
Quote:
Project is going fine but slow. All the front end should be finished in a week or two and ready to drop in the engine...That will be big time exciting!!!
__________________
Alex 1971 Lil' Red 350 SBC 700R4 |
|
|
|
|
|
11-22-2004, 08:17 PM
|
#7 | |
|
Senior Member
Join Date: Jun 2003
Location: Westminster, CO
Posts: 3,071
|
PO body man used a weld on type stud puller to straighten a slightly damaged spot. They are solid with only light surface rust on the backside. Would I soda blast the backside??? I would just to clean them up 100%, but the body guy did a very good job and they are very straight.
Quote:
__________________
Alex 1971 Lil' Red 350 SBC 700R4 |
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
