|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
12-01-2004, 06:27 PM
|
#1 |
|
user # 2756
 
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
Id these brackets please
I believe they are small block ac brackets:
   and 
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm 
|
|
|
|
12-01-2004, 06:50 PM
|
#2 |
|
graphic designer
Join Date: May 2004
Location: Spokane, Washington
Posts: 841
|
the small boomarang shaped one on the right looks like a starter brace to me. the others do apear to be SB AC stuff. I bet the boomarang one fits the stud at the fat end of the starter and bolts to the block with an existing hole/bolt.
not 100%, but that is what my starter brace looks like. |
|
|
|
|
12-01-2004, 08:38 PM
|
#3 |
|
Lovin' Life in Miss.!
Join Date: Mar 2004
Location: Puckett, Mississippi
Posts: 1,937
|
Still kinda weak on the scanner. Best I could do.
__________________
The truck... you hear that? No really, you did hear that?!!! |
|
|
|
|
12-01-2004, 08:41 PM
|
#4 | |
|
Account Suspended
Join Date: Mar 2001
Location: Virginia Beach, Va. U.S.A.
Posts: 15,320
|
Quote:
|
|
|
|
|
|
12-03-2004, 11:18 AM
|
#5 |
|
Account Suspended
Join Date: Nov 2004
Location: Deer Park, Tx.
Posts: 2,522
|
I do not want to take away from anyone's deal going on here but after the above deal is done I have some a/c brackets for a smallblock chevy that I will not be using if anyone else needs them. I will have to see how much of the original setup I have this weekend when I go home.
|
|
|
|
|
12-03-2004, 11:30 AM
|
#6 |
|
Senior Member
Join Date: Jan 2000
Location: Cincinnati, Ohio
Posts: 1,492
|
Definate starter brace for the boomerang one. I have them on both of my K20s. They do make different ones depending on your starter/engine though.
|
|
|
|
|
12-03-2004, 11:58 AM
|
#7 |
|
Registered User
Join Date: Nov 2004
Location: MINERAL WELLS WV
Posts: 143
|
The boomarang shaped one is a starter brace. A small block starter brace a big block starter brace is shorter with less curve. The bracket in the first pic just below the compressor to the right a flat bracket with 4 holes is a pass side lower alt mount for a long water pump small block. The 2 holes in the one end go to the pump the one on the other end goes thru the bottom of the alt and the hole in the middle is for a A.I.R. pump. I had this bracket on my 80 el camino ss and made one out of a plate of stainless steel without the hole for the A.I.R. pump.
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
