|
12-23-2004, 11:40 AM
|
#1 |
|
The oddest Todd around
Join Date: May 2004
Location: Miami, Florida
Posts: 1,418
|
How low?
At what point in lowering my truck should I have to worry about c-notching the frame?
72 lwb coils springs. Todd
__________________
"The greatest pleasure is to vanquish your enemies and chase them before you, to rob them of their wealth and see those dear to them bathed in tears, to ride their horses and clasp to your bosom their wives and daughters." Ghengis Khan IIOY??? |
|
|
|
12-23-2004, 11:52 AM
|
#2 |
|
Not Mine But A beauty
Join Date: Aug 2004
Location: Southern CaL
Posts: 368
|
i thinks its when you go over 4 inches
__________________
68 Chevy Shortbed 454/400 2000 Chevrolet Camaro SS 6spd 2011 Silverado 5.3 6spd auto |
|
|
|
|
12-23-2004, 12:17 PM
|
#3 |
|
The oddest Todd around
Join Date: May 2004
Location: Miami, Florida
Posts: 1,418
|
4 inches? That's it?
Well that's no good. I was wanting to do a 5 inch drop in the back. Guess I'll have to limit it to 4. Todd
__________________
"The greatest pleasure is to vanquish your enemies and chase them before you, to rob them of their wealth and see those dear to them bathed in tears, to ride their horses and clasp to your bosom their wives and daughters." Ghengis Khan IIOY??? |
|
|
|
|
12-23-2004, 12:37 PM
|
#4 |
|
Registered User
Join Date: Feb 2000
Location: Sherwood AR
Posts: 553
|
when I was running ece 6" drop coils on my '67 w/o a notch it never bottomed out.........not even when hauling a fully dressed sbc
|
|
|
|
|
12-23-2004, 01:11 PM
|
#5 |
|
Registered User
 
Join Date: Jul 2003
Location: LeRoy, Mich.
Posts: 854
|
There are a ton of people running around with 4/6 dropped trucks and NO C notches.
__________________
1968 Chevy C10 Short Fleetside/Wood floor ECE 4-6 Drop / 406 Small Block 1971 Chevelle 427 Big Block |
|
|
|
|
12-23-2004, 01:15 PM
|
#6 |
|
Registered User
Join Date: Apr 2003
Location: NB
Posts: 3,367
|
ya man! With coils you should be fine!
__________________
1968 Chevy C10 307 3ott fleetside 1967 Chevy C/10 V8, 3spd, fleetside lwb.Sold 1967 Chev C/10 step, 383, M21. SOLD |
|
|
|
|
12-23-2004, 01:35 PM
|
#7 |
|
The oddest Todd around
Join Date: May 2004
Location: Miami, Florida
Posts: 1,418
|
Cool! 4/6 drop, here I come. I figure that since I'm going to have the whole front end tore apart anyway, I might as well drop it too.
Todd
__________________
"The greatest pleasure is to vanquish your enemies and chase them before you, to rob them of their wealth and see those dear to them bathed in tears, to ride their horses and clasp to your bosom their wives and daughters." Ghengis Khan IIOY??? |
|
|
|
|
12-23-2004, 04:31 PM
|
#8 |
|
Watch out for your cornhole !
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
Todd, didn't you see me green truck?
It had 6 inch rear drop and no c-notch. It never bottomed out once in the year I drove it. Not once. Call ECE and they'll tell you everything you need to know about lowering one of these trucks. Their 6 inch rear kit is complete down to the last nuts, bolt, and widget.
__________________
I'm on the Instagram- @Gearhead_Kevin |
|
|
|
|
12-23-2004, 05:15 PM
|
#9 | |
|
The oddest Todd around
Join Date: May 2004
Location: Miami, Florida
Posts: 1,418
|
Quote:
Todd
__________________
"The greatest pleasure is to vanquish your enemies and chase them before you, to rob them of their wealth and see those dear to them bathed in tears, to ride their horses and clasp to your bosom their wives and daughters." Ghengis Khan IIOY??? |
|
|
|
|
|
12-23-2004, 07:08 PM
|
#10 |
|
Got L.E.D.s
Join Date: Dec 2004
Location: Craig Co.
Posts: 195
|
CCPs bolt in C-notch is pretty cheap. And if you have access to a welder, using a peice of 4" well casing is an option. My freind did this and it turned out good.
__________________
Bagged 1972 2wd Blazer http://www.earlyclassic.com/home.aspx |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
