Timing Problems - The 1947 - Present Chevrolet & GMC Truck Message Board Network

BLACK AND BLUE 67-72 · 01-31-2005, 10:56 PM

I recently swapped the motor into my 70 4x4 and have had a problem trying to get the engine running right. I replaced the distributor and made sure that it was on #1 TDC, the engine will start and run perfectly no miss or sputter except when I hit the gas then hesitation and backfire, when it's in gear and under a load it bogs down when the gas is applied. I have twisted the dist. every which way, if I go counter clockwise it doesn't seem to backfire as bad but when it is shut off it will not start unless it is turned back clockwise. Could a bad spark advance cause this, where it runs fine at idle and acts like that when at higher rpms? Could one work partially, at lower rpms and not higher?

mr402 · 01-31-2005, 11:35 PM

Check the centrifugal advance. Just pull the cap off and make certain it moves freely.

BLACK AND BLUE 67-72 · 02-01-2005, 11:48 PM

Thanks, I spoke to a mechanic friend of mine today and that is what he said also. Hopefully I can get home early enough tomorrow to check it.

Thanks for the reply!!

jhow66 · 02-02-2005, 12:21 AM

You need to reset your dist. -sounds like it is off a tooth or two.

02-01-2005, 11:48 PM	#3
BLACK AND BLUE 67-72 Firefighter Join Date: Feb 2001 Location: Yellville, Ar, USA Posts: 1,943	Thanks, I spoke to a mechanic friend of mine today and that is what he said also. Hopefully I can get home early enough tomorrow to check it. Thanks for the reply!! __________________ '72 Chevy SWB 350 Auto '67 GMC LWB 350 4 speed '70 Chevy 4x4 Stepside 350 Auto Yellville, Ar. USA

02-02-2005, 12:21 AM	#4
jhow66 Registered User Join Date: Jun 2002 Location: Knoxville Tenn. Posts: 3,058	You need to reset your dist. -sounds like it is off a tooth or two. __________________ 56 Chevy Bel-Air 2dr. HT (purchased new) 71 Chevy Cheyenne SWB PU (502HO) 65 GMC short bed step--work in progress and my gofer

01-31-2005, 10:56 PM	#1
BLACK AND BLUE 67-72 Firefighter Join Date: Feb 2001 Location: Yellville, Ar, USA Posts: 1,943	Timing Problems I recently swapped the motor into my 70 4x4 and have had a problem trying to get the engine running right. I replaced the distributor and made sure that it was on #1 TDC, the engine will start and run perfectly no miss or sputter except when I hit the gas then hesitation and backfire, when it's in gear and under a load it bogs down when the gas is applied. I have twisted the dist. every which way, if I go counter clockwise it doesn't seem to backfire as bad but when it is shut off it will not start unless it is turned back clockwise. Could a bad spark advance cause this, where it runs fine at idle and acts like that when at higher rpms? Could one work partially, at lower rpms and not higher? __________________ '72 Chevy SWB 350 Auto '67 GMC LWB 350 4 speed '70 Chevy 4x4 Stepside 350 Auto Yellville, Ar. USA

01-31-2005, 11:35 PM	#2
mr402 Registered User Join Date: Jan 2004 Location: Elmira, Oregon Posts: 449	Check the centrifugal advance. Just pull the cap off and make certain it moves freely.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.