Before And After ( Not Finished Yet ) - The 1947 - Present Chevrolet & GMC Truck Message Board Network

ureckme · 01-31-2005, 12:15 AM

I started with a truck that was so dirty it was black. 400SBC TH350 Locked up rear end I'll show some pics of after washing 5 times more after 10 washings.

ureckme · 01-31-2005, 12:18 AM

I'm not done, long ways to go. What do you think.

**Boog** · 01-31-2005, 12:26 AM

You did a bit more than just wash it! LOL

tablerock4 · 01-31-2005, 12:42 AM

Super Job!! It looks like mine, except mine is a long bed. What year is your truck?

ureckme · 01-31-2005, 01:06 AM

73 Chevy 406CID 305 58cc heads 194 150 Valves 268H Comp Cam 2500 Stall. 373 Gears and still look'n for more stuff to put in. Matt

badone07 · 01-31-2005, 02:53 AM

Nice job. I caught the valve cover trick.

Just curious which heads (casting numbers) you used to support that 406? Are they a set of the more common 081's or 191's?

ureckme · 01-31-2005, 04:22 AM

I dont remember the cast # I got the heads from a low Hrs. Mercruser 5.0L HO moter. Ported big time 194 / 150 165cc runners. Any way there just temp. I have a set of Sportsman ll heads going on soon. When I get headers. Oh the new heads 2.02 1.60 64cc Angle plug 200cc runners. I got a deal on them

badone07 · 01-31-2005, 02:22 PM

Ok, probably 081's or equivalent. The 191's/193's (tbi swirl ports) are around 168cc in stock form. Should be nice with the upgrades.

ureckme · 02-01-2005, 06:15 AM

I didn't use the swirl port heads my machinist said not to use them. The heads I have I did alot of bowl work and smothing bumps. They flow more then a stock 2.02 head even with the 1.94s that are in them. They screeeeem!

yfs200p · 02-03-2005, 07:13 PM

hey i was wondering what you used to clean your engine compartment. i have some mud on my motor, and i used GUNK engine brite, and it looked great while it was wet, but then like 2 hours later when it dried, all the dirt was there again..... any ideas? thanks

ureckme · 02-03-2005, 09:44 PM

Castrol purple cleaner, comes in a gl. bottel at the parts store and a steam cleaner. Then I pulled the engine and had it vatted when I rebuilt it. Matt

BowTieMan · 02-07-2005, 12:14 AM

How do you pass emissions with the 406? I am from Glendale and I am wanting to start an old chevy truck project But I am worried about passing emissions with a bigger cam and carb.

ureckme · 02-07-2005, 12:35 AM

If your running a Holley carb I'v got it down the other carbs.( no ) Im a little out of practice, This is my first hot rod in 20 years. I mostly ran Big Block Mopars and Fords. My Ford had a 538 lift 308 der cam, and a Holley DP and had no trouble passing the state tests. I would pull in the building and it would shake the hole place. The guys there took one look at the truck and said, It wont pass. They ate every word. I got a 1.28 out of a max 4.00 HC. As long as the carb is setup right,( no problem ) If you have any questions Email me at ureckmefix@cox.net Matt

CbHeEaVsYt · 02-07-2005, 07:51 AM

thats a nice lookin truck man

01-31-2005, 12:15 AM	#1
ureckme ureckmefixit2@cox.net Join Date: Dec 2004 Location: Mesa AZ. (Phoenix) Posts: 1,284	Before And After ( Not Finished Yet ) I started with a truck that was so dirty it was black. 400SBC TH350 Locked up rear end I'll show some pics of after washing 5 times more after 10 washings. Attached Images

01-31-2005, 12:18 AM	#2
ureckme ureckmefixit2@cox.net Join Date: Dec 2004 Location: Mesa AZ. (Phoenix) Posts: 1,284	I'm not done, long ways to go. What do you think. Attached Images

01-31-2005, 12:26 AM	#3
Boog laying low Join Date: Mar 2001 Location: Searcy, Ark. USA Posts: 13,535	You did a bit more than just wash it! LOL __________________ Boog 69 Chevy stepside, 358/T350, 4.11 posi, 4.5/4 drop, rallys, poboy driver primer is finer 91 Chevy sportside, Tahoe, Yukon & GMC Crewcab All GM..'nuff said. I stand for the flag and kneel at the cross

01-31-2005, 02:53 AM	#6
badone07 Project 2 Resume Join Date: May 2004 Location: Jim Thorpe, PA Posts: 884	Nice job. I caught the valve cover trick. Just curious which heads (casting numbers) you used to support that 406? Are they a set of the more common 081's or 191's? __________________ John 1984 C30 Chevy Crew Cab Dually 1998 Jeep Cherokee 4x4 2004 Chevy Trailblazer 4x4 (wife's) 1970 Mustang FB fully tubed (getting 521 BBF & powerglide) 1978 Nova 2dr (going BBCaddy & S.P. th400) 1984 Monte SS (circle track car)

01-31-2005, 02:22 PM	#8
badone07 Project 2 Resume Join Date: May 2004 Location: Jim Thorpe, PA Posts: 884	Ok, probably 081's or equivalent. The 191's/193's (tbi swirl ports) are around 168cc in stock form. Should be nice with the upgrades. __________________ John 1984 C30 Chevy Crew Cab Dually 1998 Jeep Cherokee 4x4 2004 Chevy Trailblazer 4x4 (wife's) 1970 Mustang FB fully tubed (getting 521 BBF & powerglide) 1978 Nova 2dr (going BBCaddy & S.P. th400) 1984 Monte SS (circle track car)

01-31-2005, 12:42 AM	#4
tablerock4 Registered User Join Date: Jan 2005 Location: Boise, ID Posts: 11	Super Job!! It looks like mine, except mine is a long bed. What year is your truck?

01-31-2005, 01:06 AM	#5
ureckme ureckmefixit2@cox.net Join Date: Dec 2004 Location: Mesa AZ. (Phoenix) Posts: 1,284	73 Chevy 406CID 305 58cc heads 194 150 Valves 268H Comp Cam 2500 Stall. 373 Gears and still look'n for more stuff to put in. Matt

01-31-2005, 04:22 AM	#7
ureckme ureckmefixit2@cox.net Join Date: Dec 2004 Location: Mesa AZ. (Phoenix) Posts: 1,284	I dont remember the cast # I got the heads from a low Hrs. Mercruser 5.0L HO moter. Ported big time 194 / 150 165cc runners. Any way there just temp. I have a set of Sportsman ll heads going on soon. When I get headers. Oh the new heads 2.02 1.60 64cc Angle plug 200cc runners. I got a deal on them

02-01-2005, 06:15 AM	#9
ureckme ureckmefixit2@cox.net Join Date: Dec 2004 Location: Mesa AZ. (Phoenix) Posts: 1,284	I didn't use the swirl port heads my machinist said not to use them. The heads I have I did alot of bowl work and smothing bumps. They flow more then a stock 2.02 head even with the 1.94s that are in them. They screeeeem!

02-03-2005, 07:13 PM	#10
yfs200p E.H.F.D Engine #2 Join Date: Feb 2003 Location: East Hampton, NY Long Island Posts: 916	hey i was wondering what you used to clean your engine compartment. i have some mud on my motor, and i used GUNK engine brite, and it looked great while it was wet, but then like 2 hours later when it dried, all the dirt was there again..... any ideas? thanks __________________ -NICK '72 K10 SWB Fleetside. Avocado Highlander 350-4speed-NP205 Frame Off Re-Creation '89 GMC V3500 C/C Flatbed Plow Truck 454/SM465/Np205 '15 Chevy 2500HD CCSB High Country Duramax '22 Tahoe Premier Duramax

02-03-2005, 09:44 PM	#11
ureckme ureckmefixit2@cox.net Join Date: Dec 2004 Location: Mesa AZ. (Phoenix) Posts: 1,284	Castrol purple cleaner, comes in a gl. bottel at the parts store and a steam cleaner. Then I pulled the engine and had it vatted when I rebuilt it. Matt

02-07-2005, 12:14 AM	#12
BowTieMan Registered User Join Date: Dec 2003 Location: Glendale Arizona Posts: 747	How do you pass emissions with the 406? I am from Glendale and I am wanting to start an old chevy truck project But I am worried about passing emissions with a bigger cam and carb. __________________ "A true hotrodder wouldn't be content untill he had created a car so violent, so hairy, so totally sick that the very act of dropping the hammer would result in instant death. Anything less results in the need to go faster." - Tony DeFeo

02-07-2005, 12:35 AM	#13
ureckme ureckmefixit2@cox.net Join Date: Dec 2004 Location: Mesa AZ. (Phoenix) Posts: 1,284	If your running a Holley carb I'v got it down the other carbs.( no ) Im a little out of practice, This is my first hot rod in 20 years. I mostly ran Big Block Mopars and Fords. My Ford had a 538 lift 308 der cam, and a Holley DP and had no trouble passing the state tests. I would pull in the building and it would shake the hole place. The guys there took one look at the truck and said, It wont pass. They ate every word. I got a 1.28 out of a max 4.00 HC. As long as the carb is setup right,( no problem ) If you have any questions Email me at ureckmefix@cox.net Matt

02-07-2005, 07:51 AM	#14
CbHeEaVsYt Pick up man Join Date: Feb 2005 Location: trenton mi Posts: 135	thats a nice lookin truck man



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.