327 for sale in DFW - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Jonboy · 02-13-2005, 09:26 PM

I have decided to go another route with my Blazer, and so I need to sell the engine I picked up for it. I bought the 327 form another board member, Staceydude. It has about 800 miles since the rebuild. Nothing exotic, but a solid rebuild, RV cam, and new Edelbrock dual plane intake (Performer?) and 600 Holley w/electric choke. It has chrome oil pan, timing cover, and valve covers also. This would be a great replacement for a tired engine. looking to get $800, carb to pan less distributor.

Staceydude · 02-13-2005, 10:13 PM

Hey All,

I can vouch for this motor. If I did not have the big eyes for the BBC I would buy it

back.

Runs damn good

All the parts were new like Jon said, new Holley, new manifold, new cam, new internals

etc.

On top of it all Jon is easy to deal with and one of the good guys on the board.

Regards,

Stacey

Jonboy · 02-15-2005, 05:58 PM

Anyone? Anyone?

1978steven · 02-15-2005, 08:53 PM

Do you know any of the specs on the engine, piston size, cam, heads,and so on?

Thanks,
Steven

Jonboy · 02-15-2005, 10:30 PM

I really don't know a whole lot else. I had someonme reply on another board where I have this posted that the casting number (3892657) is for 67 Camaro 302, 327, and 350 engines. This engine would actually have the small journals in that case. From the way it ran, I would guess that the pistons are not flat top, but just a stock replacement. It has an RV cam, but it isn't terribly aggressive. The engine was clean (no leaks) and looked fresh. I didn't get any reciepts, but it gave every indication of being freshly rebuilt.

1978steven · 02-16-2005, 08:39 AM

I might just rebuild my 350 I'm just seeing if it might be a little cheaper going with something already rebuilt. Thanks for the honest answer.

**N2TRUX** · 02-16-2005, 09:55 AM

Guys, I don't know squat about the motor Jonboy has for sale. I can tell you he will be as honest as possible about it though. I have dealt with Jon in the past and he went out of his way to describe my parts as honestly as possible, and was more than fair on his price....

Jonboy · 02-16-2005, 09:57 AM

FWIW, if you didn't want the carb and intake, I would sell it a bit cheaper, too.

Thanks, Ken.

02-13-2005, 09:26 PM	#1
Jonboy Slots go on anything! Join Date: May 2003 Location: Richardson, TX Posts: 5,957	327 for sale in DFW I have decided to go another route with my Blazer, and so I need to sell the engine I picked up for it. I bought the 327 form another board member, Staceydude. It has about 800 miles since the rebuild. Nothing exotic, but a solid rebuild, RV cam, and new Edelbrock dual plane intake (Performer?) and 600 Holley w/electric choke. It has chrome oil pan, timing cover, and valve covers also. This would be a great replacement for a tired engine. looking to get $800, carb to pan less distributor. __________________ 1974 Jimmy- 5.3/4L80e/NP241

02-13-2005, 10:13 PM	#2
Staceydude Registered User Join Date: Jun 2004 Location: DFW Area Texas Posts: 436	Hey All, I can vouch for this motor. If I did not have the big eyes for the BBC I would buy it back. Runs damn good All the parts were new like Jon said, new Holley, new manifold, new cam, new internals etc. On top of it all Jon is easy to deal with and one of the good guys on the board. Regards, Stacey Last edited by Staceydude; 02-13-2005 at 10:26 PM.

02-15-2005, 05:58 PM	#3
Jonboy Slots go on anything! Join Date: May 2003 Location: Richardson, TX Posts: 5,957	Anyone? Anyone? __________________ 1974 Jimmy- 5.3/4L80e/NP241

02-15-2005, 08:53 PM	#4
1978steven Registered User Join Date: Oct 2004 Location: Currently New Windsor, NY but Texas is home Posts: 332	Do you know any of the specs on the engine, piston size, cam, heads,and so on? Thanks, Steven __________________ 2002 Silverado 2500HD LB7 CCSB LT EFI Live by Rob at ATP, Edge CTS Insight DSP 5 control, S&B CAI, PPE boost valve, Pro Fab AIH, AirDog II 165, PPE WIF sensor delete plug, 5" stainless exhaust, Cognito braces & HD tie rods, H2's 315/70 R17 BFG's 2004 Tahoe LT 2006 Silverado Z71 LS 1971 Chevy C10

02-15-2005, 10:30 PM	#5
Jonboy Slots go on anything! Join Date: May 2003 Location: Richardson, TX Posts: 5,957	I really don't know a whole lot else. I had someonme reply on another board where I have this posted that the casting number (3892657) is for 67 Camaro 302, 327, and 350 engines. This engine would actually have the small journals in that case. From the way it ran, I would guess that the pistons are not flat top, but just a stock replacement. It has an RV cam, but it isn't terribly aggressive. The engine was clean (no leaks) and looked fresh. I didn't get any reciepts, but it gave every indication of being freshly rebuilt. __________________ 1974 Jimmy- 5.3/4L80e/NP241

02-16-2005, 08:39 AM	#6
1978steven Registered User Join Date: Oct 2004 Location: Currently New Windsor, NY but Texas is home Posts: 332	I might just rebuild my 350 I'm just seeing if it might be a little cheaper going with something already rebuilt. Thanks for the honest answer. __________________ 2002 Silverado 2500HD LB7 CCSB LT EFI Live by Rob at ATP, Edge CTS Insight DSP 5 control, S&B CAI, PPE boost valve, Pro Fab AIH, AirDog II 165, PPE WIF sensor delete plug, 5" stainless exhaust, Cognito braces & HD tie rods, H2's 315/70 R17 BFG's 2004 Tahoe LT 2006 Silverado Z71 LS 1971 Chevy C10

02-16-2005, 09:55 AM	#7
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,021	Guys, I don't know squat about the motor Jonboy has for sale. I can tell you he will be as honest as possible about it though. I have dealt with Jon in the past and he went out of his way to describe my parts as honestly as possible, and was more than fair on his price.... __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra"

02-16-2005, 09:57 AM	#8
Jonboy Slots go on anything! Join Date: May 2003 Location: Richardson, TX Posts: 5,957	FWIW, if you didn't want the carb and intake, I would sell it a bit cheaper, too. Thanks, Ken. __________________ 1974 Jimmy- 5.3/4L80e/NP241



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.