205 front out put ?? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

stan79chevy · 04-03-2005, 11:22 AM

my 205 has a 10 splined front yoke outout i want to turn it into one of the flange types. all of the flange type ones i can find seem to be fine splined. do they make a 10 spline flange style and does anyone have one. i want to use that style because i have a few of the cv flange driveshafts that i could use to save money.

thanks
stan

leadfoot067 · 04-03-2005, 12:35 PM

your out of luck on that one....the only way to get flange front output is to change to a 30 spline or 32 spline output...its a relatively simple swap with the case in the truck....easier yet with the case out....heres a link to a place you can get new outputs and parts for a good price and good customer service...http://www.northwestfab.com/

*1FaastC10* · 04-04-2005, 12:41 AM

www.highangledriveline.com the best in the business, period.

stan79chevy · 04-05-2005, 07:21 PM

its the 30 spline type shaft. it is for a manual tranny though. will that matter? how hard is it going to be to take the shaft out of that one and put in mine? it sounds like i could do it and not have to spend anything! which is exactly what im looking for. Know of any sites or a place where i can get directions?
thanks
stan

leadfoot067 · 04-06-2005, 12:03 AM

yes you can swap the shafts...and you can do it with the case still in the truck..i havent personally done it..but a couple of buddys of mine have...they say it isnt really hard...if i was you ide take apart the one on the floor then youll know how it goes...

stan79chevy · 04-06-2005, 06:01 PM

i got it out. but needle bearing thing fell apart. there are tiny little pill like bearings everywhere in there. ill take the one out of my truck tomorow. but when i go to put the other one back in how do i get all them little bearings to stay in there?

stan

leadfoot067 · 04-07-2005, 12:51 AM

clean and dry them and pack them in with vaseline....that will hold them...

leadfoot067 · 04-08-2005, 11:18 PM

well did you win??? did it work???

stan79chevy · 04-09-2005, 12:59 PM

all i have done so far is get the shaft i need out of the parts case and got my truck into the garage. i dont think it will be much of a problem its actually not as complicated as i thought it was going to be. im going to take the whole transmission/tcase out and reseal around the adapter where it has been leaking. i also need to fix the speedo cable from leaking. ill take some pictures so that incase someone else is doing it it may help them.

thanks
stan

04-03-2005, 11:22 AM	#1
stan79chevy Registered User Join Date: Sep 2003 Location: COVINGTON GEORGIA Posts: 477	205 front out put ?? my 205 has a 10 splined front yoke outout i want to turn it into one of the flange types. all of the flange type ones i can find seem to be fine splined. do they make a 10 spline flange style and does anyone have one. i want to use that style because i have a few of the cv flange driveshafts that i could use to save money. thanks stan __________________ 79 chevy k20 350/350/205/D44/14bFF 4.56 gears rock LWB pimer black 01 S-10 ZR2 extended cab 4.3/4L60E/233 3.73 gear 31" DICK CEPEK CRUSHERS

04-03-2005, 12:35 PM	#2
leadfoot067 horsepower junkie Join Date: Aug 2003 Location: graham, washington Posts: 326	your out of luck on that one....the only way to get flange front output is to change to a 30 spline or 32 spline output...its a relatively simple swap with the case in the truck....easier yet with the case out....heres a link to a place you can get new outputs and parts for a good price and good customer service...http://www.northwestfab.com/ __________________ 67 short wide box,350/700r4/3.73posi 71 olds cutlass "S" mom bought new..12.30s@113MPH

04-05-2005, 07:21 PM	#4
stan79chevy Registered User Join Date: Sep 2003 Location: COVINGTON GEORGIA Posts: 477	i have a 205 in my garage that has the flange i need its the 30 spline type shaft. it is for a manual tranny though. will that matter? how hard is it going to be to take the shaft out of that one and put in mine? it sounds like i could do it and not have to spend anything! which is exactly what im looking for. Know of any sites or a place where i can get directions? thanks stan __________________ 79 chevy k20 350/350/205/D44/14bFF 4.56 gears rock LWB pimer black 01 S-10 ZR2 extended cab 4.3/4L60E/233 3.73 gear 31" DICK CEPEK CRUSHERS

04-06-2005, 12:03 AM	#5
leadfoot067 horsepower junkie Join Date: Aug 2003 Location: graham, washington Posts: 326	yes you can swap the shafts...and you can do it with the case still in the truck..i havent personally done it..but a couple of buddys of mine have...they say it isnt really hard...if i was you ide take apart the one on the floor then youll know how it goes... __________________ 67 short wide box,350/700r4/3.73posi 71 olds cutlass "S" mom bought new..12.30s@113MPH

04-06-2005, 06:01 PM	#6
stan79chevy Registered User Join Date: Sep 2003 Location: COVINGTON GEORGIA Posts: 477	i did the one of the floor i got it out. but needle bearing thing fell apart. there are tiny little pill like bearings everywhere in there. ill take the one out of my truck tomorow. but when i go to put the other one back in how do i get all them little bearings to stay in there? stan __________________ 79 chevy k20 350/350/205/D44/14bFF 4.56 gears rock LWB pimer black 01 S-10 ZR2 extended cab 4.3/4L60E/233 3.73 gear 31" DICK CEPEK CRUSHERS

04-04-2005, 12:41 AM	#3
1FaastC10 Account Suspended Join Date: Oct 2002 Location: Elkhart, IN Posts: 6,400	www.highangledriveline.com the best in the business, period.

04-07-2005, 12:51 AM	#7
leadfoot067 horsepower junkie Join Date: Aug 2003 Location: graham, washington Posts: 326	clean and dry them and pack them in with vaseline....that will hold them... __________________ 67 short wide box,350/700r4/3.73posi 71 olds cutlass "S" mom bought new..12.30s@113MPH

04-08-2005, 11:18 PM	#8
leadfoot067 horsepower junkie Join Date: Aug 2003 Location: graham, washington Posts: 326	well did you win??? did it work??? __________________ 67 short wide box,350/700r4/3.73posi 71 olds cutlass "S" mom bought new..12.30s@113MPH

04-09-2005, 12:59 PM	#9
stan79chevy Registered User Join Date: Sep 2003 Location: COVINGTON GEORGIA Posts: 477	i havent gotten to it yet all i have done so far is get the shaft i need out of the parts case and got my truck into the garage. i dont think it will be much of a problem its actually not as complicated as i thought it was going to be. im going to take the whole transmission/tcase out and reseal around the adapter where it has been leaking. i also need to fix the speedo cable from leaking. ill take some pictures so that incase someone else is doing it it may help them. thanks stan __________________ 79 chevy k20 350/350/205/D44/14bFF 4.56 gears rock LWB pimer black 01 S-10 ZR2 extended cab 4.3/4L60E/233 3.73 gear 31" DICK CEPEK CRUSHERS



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.