![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Got Jesus?
Join Date: Apr 2004
Location: Ninety Six, SC
Posts: 53
|
![]()
I have a '71 C-10 Deluxe and I replaced the steering column with a manual 3 speed today. Here is my dilemma. In the yard sitting still, you can change the gears ok. When you start out on the road, it hangs between 1-2 gear. You are stuck in 1st gear until you get out and move it under the hood. Please help. I am scraping the bottom of my bucket. Thank you!
![]() |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Apr 2005
Location: Joppa, Maryland
Posts: 12
|
Sounds like the linkage bushings are worn and also the trans shifter arm bushings. Mine does the same thing at times. Just another reason that I'm getting ready to go to an automatic......
|
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: May 2004
Location: Canton North Carolina
Posts: 466
|
There is some adjustment at the shift arm's lower connection point in the engine compartment on the column itself,7/16 bolt I think- you have to loosen and move the arms forward to tighten the mechanism, the bolt at or above the bearing will take some of the slop out but this generally does not fix the problem, every three speed column I have owned needed a shift tube and or new bushings as well.
Last edited by Harold Shepard; 04-17-2005 at 10:38 AM. |
![]() |
![]() |
![]() |
#4 |
Got Jesus?
Join Date: Apr 2004
Location: Ninety Six, SC
Posts: 53
|
Harold Shepard, can you go over the adjustment in a little more detail? I think the column is ok since I can shift it fine sitting still. The strange thing is when you start moving is when is locks up. When I changed the column, is there some special way to align everything back up? The only thing I done was put the wiring harness cover directly at the bottom. I am sure you can see, I am not an expert when it comes to 67-72's. Thanks for you help.
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: May 2004
Location: Canton North Carolina
Posts: 466
|
I will get my manual out to give you the specifics and get back to you. Harold
|
![]() |
![]() |
![]() |
#6 |
Post Whore
![]() Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,684
|
Before I replaced my 3 speed with a four on the floor I had to adjust mine often.
To adjust the three speed you will need some sort of alignment rod, I used a nail cut to the right length. The linkage adjustment is made under the hood on the steering column shaft. What you want to do is loosen up the nuts that tighten the guides on the shifting linkage. Get the tranny into neutral, which will have the two guides in line with each other. The guides have a small hole in them and there is also a raised notch on top of the steering column. Lay the nail on the notch and then move the guides until the nail slides through each guide. Then what I did was moved the linkage rods up and down to see how they cycle through the gears and then get back into neutral. Then I tightened the nuts so the guide is secure. Remove the alignment rod, ie the nail, and then cycle the tranny with the shift column in the cab. I had to do a little fine tuning to get the linkage right but it took all of 10 minutes once I figured out what I was doing.
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Apr 2002
Location: Manitoba, Canada
Posts: 663
|
How old is the three speed column? It could be bushings, but in my experience it might not be. When I bought my '69 the shifter was so tight that I couldn't even shift it into first - I broke the little knob off the end of the shifter. Believe it or not, WD-40 was the answer. I removed the wheel and sprayed inside the column and under the hood I sprayed into all the openings of the column. After working it a bit it shifts like new.
__________________
Present: 2015 Tacoma. Yeah, not a GM, but I love it. 1969 GMC 32,000 - fix, drive, relax, fix... 2019 BMW R1250 GSA - Yahoooooooo 1979 Honda GL 1000 - retro touring at its best. Past: '05 Sierra 4x4 - Had 270,000 KM and running well when it was written-off by a stop sign runner. '94 F-150 from the "F word" company. I'll admit it...good truck. Sold what was left of it for $800 to a guy who came to pick it up at 11:00 PM with cash in hand. Hmm. '79 Sierra Grande (Black) organ donor - perfect rebuildable 4-bolt 350 and a good TH350. '76 Sierra Grande (Orange) - hate isn't too strong a word. Kid who bought it turned it into a hot rod. '68 C-10 R.I.P. - Dad's old truck...too far gone to resurrect. '59 C-50 - with hoist. Truck is gone, wife isn't. Nuff said. |
![]() |
![]() |
![]() |
#8 |
Got Jesus?
Join Date: Apr 2004
Location: Ninety Six, SC
Posts: 53
|
To all, this is great information. I will try it out tommorrow evening. I have to go into work at 3-4 am tommorrow morning, so I must go to bed soon.
|
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: May 2004
Location: Oklahoma City
Posts: 205
|
I did the same thing as Bluec10. Mine is an auto but that WD-40 works miracles. I had just about broken my shifter off of the column and I thought what the hell it can't hurt it that bad to spray it. Shifts like a new truck now.
__________________
1969 chevy C10 long bed 350 4bbl auto p/disc and 5 lug |
![]() |
![]() |
![]() |
#10 |
Got Jesus?
Join Date: Apr 2004
Location: Ninety Six, SC
Posts: 53
|
Ok, thanks to all of your help! I think the problem lies in the bushings on the transmission shifter arms. The steering column shifter bushings are good and tight. The ones on the transmission arms are gone. Does anyone have any or know of where I can get these? Thank you again for all the help.
|
![]() |
![]() |
![]() |
#11 |
Senior Member
![]() Join Date: Feb 2003
Location: WIS
Posts: 1,752
|
shift arm bushings.
I don't know if they're available, but I made some last week for my '72 stepside out of the brass tube from an air nozzle. Correct ID & OD. Just cut to proper length............Zoomy
|
![]() |
![]() |
![]() |
#12 |
Registered User
Join Date: Jan 2004
Location: Camarillo, Ca
Posts: 79
|
I had the exact same problem. I took it in and had the mechanic replace the bushings. Solved the problem. Now I have to figure out if I need to do it again or just oil and adjust it. I'm starting to wonder if an automatic might be a good purchase.
__________________
1972 1/2 ton Chevy C10 V-8 350, crate engine, with Flomaster dual exhaust. She's Old Blue the Truckinator (no relation to Arnold ![]() |
![]() |
![]() |
![]() |
#13 |
'Burban Legend
![]() Join Date: Apr 2005
Location: Mingo Junction OH
Posts: 918
|
Old Trick
Mine was 3 on tree factory. Now TH400, on the way back to a 4-speed. The guy that sold me mine showed me how to make it work if it jams up. Just push with your thumb 180 degrees from the shifter lever and it will probably keep you from busting the lever off. As far as while driving, I'm sure that's a torque issue. Mine will be a slick column with a hole in the floor soon. HotRod
|
![]() |
![]() |
![]() |
Bookmarks |
|
|