![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Jun 2004
Location: Beeville, Texas
Posts: 1,943
|
FS: 1972 SWB C10 frame and cab, NO bed or front clip
Just scored a 72 C10 SWB frame and cab for $25! I don't need it, but I figured somebody in Texas might want it. First off, I don't have a title, but the frame numbers and door VIN tag match. It's an A/C truck, has the controls, cables, but it's not complete. It has no motor, tranny, or driveshaft. The rear end is there, not sure of the ratio and it's a coil spring rear, but for some reason the coils are gone?
![]() ![]() ![]() EDIT: The rear end doesn't come with the truck, but I'll sell it for $50. I can check the gear ratio if there is any interest.
__________________
RJD 1984 Chevrolet C30 welding truck 454/SM465 1977 GMC C15 pickup 350/TH350 1970 Chevrolet C20 pickup 350/TH400 1970 Chevrolet K20 Suburban 454/TH350 1969 GMC 8500 478M V6/5 spd winch truck Last edited by Robert1970C20rstbukt; 05-26-2005 at 01:14 PM. |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: May 2001
Location: Benbrook, TX
Posts: 1,060
|
I'll take it, if the the frame is straight.
What is the zip code
__________________
69 swb stepside, rebuild and upgrade in progress |
![]() |
![]() |
![]() |
#3 |
Active Member
![]() Join Date: Feb 2004
Location: Fort Worth, TX
Posts: 122
|
Let me know if matt67350 decides not to take it. My folks live in Beeville, so coming down to get it would be no problem. What does the cab look like in the door sill area and the kick panel/floor area?
matt67350, Beeville is about 330 miles south of Ft. Worth, between San Antonio and Corpus Christi. |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Jun 2004
Location: Beeville, Texas
Posts: 1,943
|
OK, as far as rust, this cab is fixable. Both rockers and cab corners are going to need to be replaced. The roof looks good, but it has some rust coming through on the passenger side driprail going down the side of the cab. There is some rot on the passenger side of the dash around the glovebox too. I have no idea if the frame is straight, the only thing I can do is eyeball it. I forgot to add that the rear end doesn't come with the truck, but can be bought for $50.
__________________
RJD 1984 Chevrolet C30 welding truck 454/SM465 1977 GMC C15 pickup 350/TH350 1970 Chevrolet C20 pickup 350/TH400 1970 Chevrolet K20 Suburban 454/TH350 1969 GMC 8500 478M V6/5 spd winch truck |
![]() |
![]() |
![]() |
#5 |
Hot Rods For Life
Join Date: Sep 2001
Location: Waxahachie, TX
Posts: 3,305
|
Where is Beeville?
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Jun 2004
Location: Beeville, Texas
Posts: 1,943
|
Down south about an hour from Corpus Christi.
__________________
RJD 1984 Chevrolet C30 welding truck 454/SM465 1977 GMC C15 pickup 350/TH350 1970 Chevrolet C20 pickup 350/TH400 1970 Chevrolet K20 Suburban 454/TH350 1969 GMC 8500 478M V6/5 spd winch truck |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: May 2001
Location: Benbrook, TX
Posts: 1,060
|
Robert, I'll have to pass on the frame.
Thanks for the info. and the pm. Matthew
__________________
69 swb stepside, rebuild and upgrade in progress Last edited by matt67350; 05-26-2005 at 07:31 PM. |
![]() |
![]() |
![]() |
#8 |
Active Member
![]() Join Date: Feb 2004
Location: Fort Worth, TX
Posts: 122
|
Robert, I will pass on the cab. I was hoping that a South Texas cab would be in better shape than the one I have.
Thanks. |
![]() |
![]() |
![]() |
Bookmarks |
|
|