vent rubber question (pics) - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Scooter67 · 06-04-2005, 03:34 PM

Is the bottom edge supposed to tuck down inside the door? Just installed new vent rubber and no matter what I do it won't lay flat against the door. Old vent rubber was like this too.

jhow66 · 06-04-2005, 04:00 PM

Inside

kaycee · 06-04-2005, 10:50 PM

I put mine on the out side they fit pretty good this way it didn't make since to have them run inside and let the water get inside door.But if mine came out like that I would put them inside.OH well I tend to do things different

kelsfine69 · 06-04-2005, 11:54 PM

they go inside, the small amount of water that might go thru will drain out the bottom drain holes in the door

Scooter67 · 06-05-2005, 11:28 AM

Went ahead and tucked it in. Looks alot better. It makes some contact with the outer door, so hopefully won't let alot of water in the door. Betcha the rubber that came on the truck was wide enough for a good seal! It can be hard to find aftermarket stuff as good as original.

**Yukon Jack** · 06-05-2005, 06:36 PM

Much better!

06-04-2005, 03:34 PM	#1
Scooter67 Registered User Join Date: Jan 2005 Location: middle TN Posts: 87	vent rubber question (pics) Is the bottom edge supposed to tuck down inside the door? Just installed new vent rubber and no matter what I do it won't lay flat against the door. Old vent rubber was like this too. __________________ Here's my '67 stepside www.truckwithaheart.com Last edited by Scooter67; 06-05-2005 at 11:25 AM.

06-04-2005, 04:00 PM	#2
jhow66 Registered User Join Date: Jun 2002 Location: Knoxville Tenn. Posts: 3,058	Inside __________________ 56 Chevy Bel-Air 2dr. HT (purchased new) 71 Chevy Cheyenne SWB PU (502HO) 65 GMC short bed step--work in progress and my gofer

06-04-2005, 10:50 PM	#3
kaycee Registered User Join Date: Jan 2000 Location: Wyoming USA Posts: 2,463	I put mine on the out side they fit pretty good this way it didn't make since to have them run inside and let the water get inside door.But if mine came out like that I would put them inside.OH well I tend to do things different __________________ 2001 Silverado K-1500 2005 FXDWG stage3 69 CHEVY Short/Step 327/4L60 373 posi 63 IMPALA 327/4L60

06-05-2005, 11:28 AM	#5
Scooter67 Registered User Join Date: Jan 2005 Location: middle TN Posts: 87	Went ahead and tucked it in. Looks alot better. It makes some contact with the outer door, so hopefully won't let alot of water in the door. Betcha the rubber that came on the truck was wide enough for a good seal! It can be hard to find aftermarket stuff as good as original. __________________ Here's my '67 stepside www.truckwithaheart.com

06-05-2005, 06:36 PM	#6
Yukon Jack Post Whore Join Date: Feb 2000 Location: Rose Hill, KS, USA Posts: 12,689	Much better! __________________ 1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14

06-04-2005, 11:54 PM	#4
kelsfine69 18 Till I Die Join Date: Mar 2005 Location: Alberta, Canada Posts: 1,522	they go inside, the small amount of water that might go thru will drain out the bottom drain holes in the door



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.