Bodywork progress 72 burb *56k beware* - The 1947 - Present Chevrolet & GMC Truck Message Board Network

*Sublvr72* · 03-23-2005, 05:05 AM

Well, I sold the Mustang out at my parents house and I did not have a ride back to my place so I drove the burb back... I started getting tired of looking at all the dents in it and I decided to do something about it. Went to my buddies shop and used his stinger dent puller (the type where you fuse a rod to the body and pull the rod with the slide hammer to pull the metal back out) Pretty cool tool IMO...I also welded up some holes and welded a plate in to shave the sidemarker.

This was before

yes thats duct tape over the sidemarker hole and a whole lot of bondo covering the damaged panel

and After...

Here is the truck just sitting at my place...

Took it out and did this...

It used to look something like this side before...This is going to be next Sunday's project.

With this just about completely pulled I am just about ready to try to install the caddy lights I have. I think I might attempt this on my own...

I also did a little work on this door.

LUV2XCLR8 · 03-23-2005, 11:58 AM

*ghetocrewzer* · 06-05-2005, 09:06 PM

Man i just saw this, lookin good!!!!!! Hope to get back to work on mine soon finishing few small fab projects then start skimming whole body and long boarding it....

How's urs comin now

cojnit · 06-06-2005, 06:32 PM

his is for sale

03-23-2005, 05:05 AM	#1
Sublvr72 Account Suspended Join Date: May 2004 Location: Simi Valley, CA Posts: 1,387	Bodywork progress 72 burb 56k beware Well, I sold the Mustang out at my parents house and I did not have a ride back to my place so I drove the burb back... I started getting tired of looking at all the dents in it and I decided to do something about it. Went to my buddies shop and used his stinger dent puller (the type where you fuse a rod to the body and pull the rod with the slide hammer to pull the metal back out) Pretty cool tool IMO...I also welded up some holes and welded a plate in to shave the sidemarker. This was before yes thats duct tape over the sidemarker hole and a whole lot of bondo covering the damaged panel and After... Here is the truck just sitting at my place... Took it out and did this... It used to look something like this side before...This is going to be next Sunday's project. With this just about completely pulled I am just about ready to try to install the caddy lights I have. I think I might attempt this on my own... I also did a little work on this door.

03-23-2005, 11:58 AM	#2
LUV2XCLR8 The LuvShack Garage Join Date: Jan 2004 Location: Maple Grove, TN (West Side) Posts: 30,468	__________________ Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T

06-05-2005, 09:06 PM	#3
ghetocrewzer Account Suspended Join Date: Feb 2004 Location: Sallis,MS Posts: 479	Man i just saw this, lookin good!!!!!! Hope to get back to work on mine soon finishing few small fab projects then start skimming whole body and long boarding it.... How's urs comin now Last edited by ghetocrewzer; 06-05-2005 at 09:06 PM.

06-06-2005, 06:32 PM	#4
cojnit Nothing clever Join Date: Jun 2003 Location: Kailua HI Posts: 828	his is for sale __________________ Got "the Midas Touch!"



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.