Whats this? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Patch · 06-24-2005, 12:13 AM

This piece on my blazer is toast....what is it, and are they available? Thanks......

Alexis · 06-24-2005, 12:55 AM

What part?

The inner rocker, the rocker box rears side plate, the floor, or the wall that the rear of the floor pans connect too? There is like 4 different things in that one picture.

or the missing bed panel?

donkey69 · 06-24-2005, 01:49 AM

....you can get new tires!!

71jimmy · 06-24-2005, 02:49 AM

You cracked me up donkey69, thanks I needed that!!!!!!!

Patch · 06-24-2005, 04:08 AM

I should of known better with you guys... The darn thing in the middle....some sort of support or something? The back end of the rocker attaches to it, and if you reach up through the wheel well you can touch it...(it has a drain plug in the back side of it.)

vtblazer · 06-24-2005, 06:32 AM

If your asking about the verticle part that the bed floor sits on, I've never seen one reproduced.

Best bet is to find someone parting out a blazer/jimmy and get them to cut it off for you.

Or get creative with metal working and build/replace the part.

It'll be covered up by the quarter and rocker anyway.

Good luck.

**raggedjim** · 06-24-2005, 02:18 PM

If it is this piece you'll have to fix it yourself, mine are bad too...
http://67-72chevytrucks.com/vboard/s....php3?t=138437

Rg

Patch · 06-24-2005, 08:12 PM

The first one is the outside...then the inside.....so these aren't available? Hmmmmm......

Patch · 06-24-2005, 08:26 PM

I am talking about the panel with the plug in it.....not the quarter panel.....just taking away that opportunity for wise guys part two......

Thanks for the feeback!

Patch · 06-25-2005, 01:59 PM

Anyone at all??????

vtblazer · 06-25-2005, 02:09 PM

You should be able to buy the patch panel for the outside panel but you still will need the inner suport.
I can check, I think the quarter I just replaced still has a good one.

vtblazer · 06-25-2005, 02:11 PM

Oh yeah, one more thing...OUCH!!

Patch · 06-25-2005, 05:01 PM

Whats really scary is its been repaired by someone before.........yeah......o.k.
I have a new patch panel...got it from Classic heartbeat...but that support bracket behind it(is that what its called?) I guess I'll have to make one huh?
Thanks for the feed back......The drivers' side looks just like this side...and it was previously repaired too......gggrrrrr!!!!!!

Patch · 06-25-2005, 05:02 PM

I just re-read your post....you might have that support piece? If so....how much and when??? LOL!!!! Thanks for looking.....

Patch · 06-25-2005, 05:04 PM

You still have that hammered pass bedside? I need a piece of wheel well lip..???

vtblazer · 06-25-2005, 05:10 PM

Yeah still have it, I never throw anything away...

I think I'm going up to the shop on Sunday, I'll check it out.

Patch · 06-25-2005, 05:17 PM

That would be cool if your not saving that section for yourself....I need this section right here..... and the other is my drivers side.......very sad...lol

vtblazer · 06-28-2005, 06:41 AM

Quote:

Originally Posted by Patch

I need a piece of wheel well lip.

I thought you wanted the inner support...?
I'll check the lip too.

Sorry, didn't make it this weekend, soon though.

Patch · 06-28-2005, 10:46 PM

I need that inner support.....and a section to replace that lip....if you dont want to get rid of the lip...no problem. I'll take what I can get. Do you know what you'll be wanting for the inner support if you have it? Let me know.....whenever.....no rush. Thanks

06-24-2005, 12:13 AM	#1
Patch Senior Member Join Date: Jul 2002 Location: Oak Harbor, WA Posts: 709	Whats this? This piece on my blazer is toast....what is it, and are they available? Thanks...... Attached Images __________________ Patch

06-24-2005, 12:55 AM	#2
Alexis Member since 2000 Join Date: Dec 2000 Location: Mountain View Ca / Mexico Posts: 7,874	What part? The inner rocker, the rocker box rears side plate, the floor, or the wall that the rear of the floor pans connect too? There is like 4 different things in that one picture. or the missing bed panel? Last edited by Alexis; 06-24-2005 at 01:59 AM.

06-24-2005, 01:49 AM	#3
donkey69 JB-80 &quot;Twice as Good&quot; Join Date: Jun 2004 Location: Central, MN Posts: 354	....you can get new tires!! __________________ HEY NOW!

06-24-2005, 02:49 AM	#4
71jimmy Registered User Join Date: Mar 2004 Location: Sacramento, CA Posts: 1,083	You cracked me up donkey69, thanks I needed that!!!!!!! __________________ '71 Jimmy, 350, SM465, NP205, 2in Tuff Country lift, 33s on rallies, TBI, softtop and hardtop "If life was fair you'd be able to afford one of each and a garage large enough to house them all."

06-24-2005, 04:08 AM	#5
Patch Senior Member Join Date: Jul 2002 Location: Oak Harbor, WA Posts: 709	Okay Jokers I should of known better with you guys... The darn thing in the middle....some sort of support or something? The back end of the rocker attaches to it, and if you reach up through the wheel well you can touch it...(it has a drain plug in the back side of it.) __________________ Patch

06-24-2005, 06:32 AM	#6
vtblazer Registered User Join Date: Oct 2003 Location: Central Vermont Posts: 8,537	If your asking about the verticle part that the bed floor sits on, I've never seen one reproduced. Best bet is to find someone parting out a blazer/jimmy and get them to cut it off for you. Or get creative with metal working and build/replace the part. It'll be covered up by the quarter and rocker anyway. Good luck.

06-24-2005, 02:18 PM	#7
raggedjim Senior Member Join Date: Jun 2002 Location: Murray, Kentucky Posts: 3,514	If it is this piece you'll have to fix it yourself, mine are bad too... http://67-72chevytrucks.com/vboard/s....php3?t=138437 Rg __________________ Roger '68 Short step - https://67-72chevytrucks.com/vboard/...d.php?t=849675 '69 ('70?) 2wd Blazer '70 GMC Jimmy 2wd '73 Firebird - https://67-72chevytrucks.com/vboard/...d.php?t=853203 Ideas - https://67-72chevytrucks.com/vboard/...d.php?t=851743 Last edited by raggedjim; 06-24-2005 at 02:19 PM. Reason: forgot link...

06-24-2005, 08:12 PM	#8
Patch Senior Member Join Date: Jul 2002 Location: Oak Harbor, WA Posts: 709	This is my problem The first one is the outside...then the inside.....so these aren't available? Hmmmmm...... Attached Images __________________ Patch

06-24-2005, 08:26 PM	#9
Patch Senior Member Join Date: Jul 2002 Location: Oak Harbor, WA Posts: 709	Clarification I am talking about the panel with the plug in it.....not the quarter panel.....just taking away that opportunity for wise guys part two...... Thanks for the feeback! __________________ Patch

06-25-2005, 01:59 PM	#10
Patch Senior Member Join Date: Jul 2002 Location: Oak Harbor, WA Posts: 709	Anyone? Anyone at all?????? __________________ Patch

06-25-2005, 02:09 PM	#11
vtblazer Registered User Join Date: Oct 2003 Location: Central Vermont Posts: 8,537	You should be able to buy the patch panel for the outside panel but you still will need the inner suport. I can check, I think the quarter I just replaced still has a good one. Attached Images

06-25-2005, 02:11 PM	#12
vtblazer Registered User Join Date: Oct 2003 Location: Central Vermont Posts: 8,537	Oh yeah, one more thing...OUCH!! Last edited by vtblazer; 06-25-2005 at 02:12 PM.

06-25-2005, 05:01 PM	#13
Patch Senior Member Join Date: Jul 2002 Location: Oak Harbor, WA Posts: 709	No Kidding!!! Whats really scary is its been repaired by someone before.........yeah......o.k. I have a new patch panel...got it from Classic heartbeat...but that support bracket behind it(is that what its called?) I guess I'll have to make one huh? Thanks for the feed back......The drivers' side looks just like this side...and it was previously repaired too......gggrrrrr!!!!!! __________________ Patch

06-25-2005, 05:02 PM	#14
Patch Senior Member Join Date: Jul 2002 Location: Oak Harbor, WA Posts: 709	Okay... I just re-read your post....you might have that support piece? If so....how much and when??? LOL!!!! Thanks for looking..... __________________ Patch

06-25-2005, 05:04 PM	#15
Patch Senior Member Join Date: Jul 2002 Location: Oak Harbor, WA Posts: 709	One more thing... You still have that hammered pass bedside? I need a piece of wheel well lip..??? __________________ Patch



Register or Log In To remove these advertisements.

06-25-2005, 05:10 PM	#16
vtblazer Registered User Join Date: Oct 2003 Location: Central Vermont Posts: 8,537	Yeah still have it, I never throw anything away... I think I'm going up to the shop on Sunday, I'll check it out.

06-25-2005, 05:17 PM	#17
Patch Senior Member Join Date: Jul 2002 Location: Oak Harbor, WA Posts: 709	Thanx! That would be cool if your not saving that section for yourself....I need this section right here..... and the other is my drivers side.......very sad...lol Attached Images __________________ Patch Last edited by Patch; 06-25-2005 at 05:18 PM.

06-28-2005, 10:46 PM	#19
Patch Senior Member Join Date: Jul 2002 Location: Oak Harbor, WA Posts: 709	Both I need that inner support.....and a section to replace that lip....if you dont want to get rid of the lip...no problem. I'll take what I can get. Do you know what you'll be wanting for the inner support if you have it? Let me know.....whenever.....no rush. Thanks __________________ Patch

Register or Log In To remove these advertisements.