? about roll pan - The 1947 - Present Chevrolet & GMC Truck Message Board Network

CHEVYE · 06-27-2005, 11:02 PM

this might be a dumb one but i was trial fitting my roll pan tonight and it appears i have to notch out the bed to fit the lisc. plate box. just wanted to know if that sounds familiar to anyone before i get to hackin. it is a sir michael's if that makes a diff.

gchemist · 06-27-2005, 11:14 PM

I didn't have to notch mine. My roll pan is a Mar-k product though.

CHEVYE · 06-27-2005, 11:24 PM

here's where it hits. the pan doesn't drop in the middle near the plate, it stays the same all the way across.

gchemist · 06-28-2005, 05:45 AM

That roll pan has one big plate box. Looks like you will have to notch the bed rail.

milehightoyz · 06-28-2005, 03:46 PM

i dont quite get that pic.....it appears the platebox is behind the pan itself??, and why is it so deep? at any rate, if the second pic is taken witht he rollpan at the same height as your first pic that could be your problem. that pan needs to be up farther another 2" or so so that your body line lines up. that will pull the pan out farther and probably allow your plate box to sit flush against that rail. hope this helps.

CHEVYE · 06-28-2005, 04:22 PM

i just quick clamped it where it stopped itself. i don't know why it's so deep. now i'm debating even welding it up

. i might try to get the kind "bigarmzz" has that slants down in the middle.

pedrofixlater · 06-28-2005, 04:27 PM

I had to cut out my rear cross but mine is a stepside I got mine from
mar-k.com

82c10 · 06-28-2005, 04:30 PM

see if you can slide it in from the top somehow, if it won't take where the plate box goes on and make it recess in the rollpan less, just some ideas

75stepside · 06-28-2005, 04:43 PM

Quote:

Originally Posted by pedrofixlater

I had to cut out my rear cross but mine is a stepside I got mine from
mar-k.com

same here... got my stepside pan from www.mar-k.com ...do you have a pic of yours on?

CHEVYE · 06-28-2005, 04:56 PM

it won't go anyway i try it. looks like it's time to cut either the bed or the plate box on the pan

.

milehightoyz · 06-28-2005, 05:23 PM

if you decide not to use it ill buy it i need it for my 82 shortwide =)

84slopwaggin · 06-28-2005, 11:31 PM

Maybe it's just the wrong year roll pan.

bagged_and_bodydrop · 06-29-2005, 01:15 AM

I cut the part out of the bed on mine, and mine is a Mark-K no big deal to cut it, and mine lines up pefectly after I cut that piece out. So I'd say cut away. Just not to much.

06-27-2005, 11:02 PM	#1
CHEVYE my gas saver Join Date: Sep 2003 Location: Clarksville, TN Posts: 2,046	? about roll pan this might be a dumb one but i was trial fitting my roll pan tonight and it appears i have to notch out the bed to fit the lisc. plate box. just wanted to know if that sounds familiar to anyone before i get to hackin. it is a sir michael's if that makes a diff. __________________ 85' SWB, 4.3/TH350, getting ready for paint 84`SWB, 462ci./TH400, cowl hood, 15" billet spec., flows, blazer buckets/console, flat black 71`SWB, project ebay feedback

06-27-2005, 11:14 PM	#2
gchemist BAD BOW-Silverado XST Join Date: May 2000 Location: Senior Member from Austin, TX Posts: 6,431	I didn't have to notch mine. My roll pan is a Mar-k product though. __________________ Gerardo a.k.a. Mad Chemist Silverado XST videos

06-27-2005, 11:24 PM	#3
CHEVYE my gas saver Join Date: Sep 2003 Location: Clarksville, TN Posts: 2,046	here's where it hits. the pan doesn't drop in the middle near the plate, it stays the same all the way across. Attached Images __________________ 85' SWB, 4.3/TH350, getting ready for paint 84`SWB, 462ci./TH400, cowl hood, 15" billet spec., flows, blazer buckets/console, flat black 71`SWB, project ebay feedback

06-28-2005, 04:22 PM	#6
CHEVYE my gas saver Join Date: Sep 2003 Location: Clarksville, TN Posts: 2,046	i just quick clamped it where it stopped itself. i don't know why it's so deep. now i'm debating even welding it up . i might try to get the kind "bigarmzz" has that slants down in the middle. __________________ 85' SWB, 4.3/TH350, getting ready for paint 84`SWB, 462ci./TH400, cowl hood, 15" billet spec., flows, blazer buckets/console, flat black 71`SWB, project ebay feedback

06-28-2005, 04:27 PM	#7
pedrofixlater 75 STEPSIDE Join Date: Mar 2005 Location: Suffolk, VA Posts: 92	roll pan I had to cut out my rear cross but mine is a stepside I got mine from mar-k.com __________________ Pete 75 Chevy Stepside 70 Buick Skylark/GS

06-28-2005, 05:45 AM	#4
gchemist BAD BOW-Silverado XST Join Date: May 2000 Location: Senior Member from Austin, TX Posts: 6,431	That roll pan has one big plate box. Looks like you will have to notch the bed rail.

06-28-2005, 03:46 PM	#5
milehightoyz AttentionDeficitDisorder Join Date: Mar 2005 Location: COLORADO Posts: 600	i dont quite get that pic.....it appears the platebox is behind the pan itself??, and why is it so deep? at any rate, if the second pic is taken witht he rollpan at the same height as your first pic that could be your problem. that pan needs to be up farther another 2" or so so that your body line lines up. that will pull the pan out farther and probably allow your plate box to sit flush against that rail. hope this helps.

06-28-2005, 04:30 PM	#8
82c10 needin' money Join Date: May 2005 Location: Chickasha, Oklahoma Posts: 1,106	see if you can slide it in from the top somehow, if it won't take where the plate box goes on and make it recess in the rollpan less, just some ideas

06-28-2005, 04:56 PM	#10
CHEVYE my gas saver Join Date: Sep 2003 Location: Clarksville, TN Posts: 2,046	it won't go anyway i try it. looks like it's time to cut either the bed or the plate box on the pan . __________________ 85' SWB, 4.3/TH350, getting ready for paint 84`SWB, 462ci./TH400, cowl hood, 15" billet spec., flows, blazer buckets/console, flat black 71`SWB, project ebay feedback

06-28-2005, 05:23 PM	#11
milehightoyz AttentionDeficitDisorder Join Date: Mar 2005 Location: COLORADO Posts: 600	if you decide not to use it ill buy it i need it for my 82 shortwide =)

06-28-2005, 11:31 PM	#12
84slopwaggin Registered User Join Date: Apr 2005 Location: Ar Posts: 558	Maybe it's just the wrong year roll pan.

06-29-2005, 01:15 AM	#13
bagged_and_bodydrop Just drag it Join Date: Dec 2004 Location: ardmore, oklahoma Posts: 98	I cut the part out of the bed on mine, and mine is a Mark-K no big deal to cut it, and mine lines up pefectly after I cut that piece out. So I'd say cut away. Just not to much.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.