|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
08-27-2002, 09:42 PM
|
#1 |
|
Registered User
Join Date: Jan 2002
Location: Calgary, Alberta, Canada
Posts: 451
|
Question about dip stick tube in engine block
I have a new chrome dipstick set. The tube into the block seems to just push into the block hole. Before I damage the stock one, removing it. Does it just pull out of the hole in the block, maybe by using some vise grips?
I tryed wiggling the stock one on the weekend , and it seemed to be firmly in place. I don't want to twist and pull until I know that it is o.k. to do so. Also , does the new one just press in, and seal o.k. with no silicone?
__________________
72 C10 Cheyenne Super Full trim Factory tach dash A/C dash Factory tilt 350 / 350 power train - with Edelbrock components. |
|
|
|
08-27-2002, 10:14 PM
|
#2 |
|
Account Suspended
Join Date: May 2000
Location: IL
Posts: 0
|
theres a trick to pull one out, and i forgot how its done now, hmmmm
have learned too much new lately and forgotten some old.... well, one way is to get a bolt or piece of rod that will slip into inside of top of the tube and get rags around the tube and use vise grips and try that way,, or something similar, when you renistall then you need to use long screwdriver or punch on the lip at the base of the tube down there to drive the tube down, if its kinda not real tight fitting then use some RTV black on it, good luck |
|
|
|
|
08-27-2002, 10:16 PM
|
#3 |
|
Registered User
Join Date: Mar 2001
Location: Burien, WA, USA
Posts: 391
|
It should just pop out (assuming mine were all meant to), I wouldn't bother with any silicone unless it keeps slipping out or moving around.
RainDog
__________________
"Every normal man must be tempted at times to spit on his hands, hoist the black flag, and begin slitting throats." |
|
|
|
|
08-27-2002, 11:10 PM
|
#4 |
|
Registered User
 
Join Date: Oct 2001
Location: Southern New Mexico
Posts: 649
|
I have twisted them out with pliers. They are supposed to be a bit snug and should require a little force to get them out.
|
|
|
|
|
08-27-2002, 11:24 PM
|
#5 |
|
Registered User
Join Date: Aug 2001
Location: SOMERSET KY.
Posts: 6,427
|
 YEP ... I JUST LATCH ONTO IT NEAR THE BLOCK WITH VICEGRIPS, TURN BACK & FORTH & PULL UP. I LIKE TO PUT A LITTLE SILICON AROUND THE NEW ONE JUST BELOW THE BULGE, DROP A 3/8" BOLT INTO THE TOP END, & TAP IT INTO PLACE IN THE HOLE UNTIL IT SEATS.
__________________
junkyardjohn 69 1 TON TOW TRUCK // 84 4WD CUCV BLAZER// 85 1 TON 4WD STAKE TRUCK// 86 M1031 5/4 TON 4WD CUCV// ALOT OF OLD TRUCKS FOR ONE OLD MAN TO DRIVE.  THERES ROOM FOR ALL OF GODS CREATURES RIGHT NEXT TO MY MASHED POTATOES//LIFE MEMBER OF P.E.T.A (PEOPLE EATING TASTY ANIMALS) DON'T RENT U-HAUL ALWAYS TELL THE TRUTH IT WILL AMAZE PART OF THE PEOPLE & ASTONISH THE REST |
|
|
|
|
08-27-2002, 11:37 PM
|
#6 |
|
"Ochre Ogre"
Join Date: Apr 2000
Location: Springfield, MN
Posts: 3,558
|
I have used a 1/2" wrench to seat the new tube also. Slide it over the tube and tap on the wrench with a hammer until it is seated.
As far as removal. I have just wiggled it and it will slide out as you pull.
__________________
Bowtie Truck Stop Inc. Mid-West GM Truck Restoration Parts Supplier Your Key Parts, Auto Metal Direct, Dynacorn, and Goodmark dealer. like us @ www.facebook.com/BowtieTruckStop 1971 C-10 Suburban (Ochre) 1971 K-10 Suburban (Ochre) 1972 C-10 Suburban (Ochre) 1972 K-20 Suburban (Yellow- that just aint right!) Springfield, Minnesota 56087 |
|
|
|
|
08-28-2002, 01:44 AM
|
#7 |
|
Recovering Truck Driver
Join Date: Mar 2002
Location: Orleans, NE USA
Posts: 1,883
|
yep, i agree with da-burb.....wiggle the old one out, use pliers if nescessary, and put a wrench over the tube, rest it on the lip and smack the wrench with a hammer.
__________________
67 K-20 350, SM465, Eaton rear, 4.56 no spin option 00 Dodge 2500 4x4, 24V cummins, 5 speed Chad South Central Nebraska |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
