WTB: SB 400 and rear end - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Larry68GMC · 10-06-2005, 03:13 PM

Just got back from Iraq and looking for a complete SB 400, would be interested in just the long block as well, within a few hours of Oklahoma City. Also a 3:73 or 4:10 5 lug posi with leafs...Thanks...Larry

Jakes-66-K10 · 10-06-2005, 03:30 PM

How much you looking to spend? I have a built one with vortec heads with intake manifold I was going to use on my '66... but it's just sitting around doing nothing for about 6 weeks now.

cst70rocket · 10-06-2005, 03:35 PM

Larry, there is a guy in Wichita Falls,Tx with a stock 400 short block, never been torn down, standard bore. He is asking $300 for it and you pick it up. Very nice guy. I just bought the rotating assy from him. His name is Scott Schultz, his number is 940-631-5865 You can tell him that Kirk from San Angelo sent ya.
Kirk

cst70rocket · 10-06-2005, 03:38 PM

I may also have a buddy with a later model 10 bolt with fresh posi,new 3.73 gears and new brakes/drums if he still has it, he was asking $500 for it. It's leaf sprung, and I believe it's a bolt in, but don't quote me on that. If interested, email me.
cst70rocket@yahoo.com
Kirk

Larry68GMC · 10-07-2005, 11:20 AM

Thanks for the info cst70, How much you asking and what are the specs Vortex? Thanks...guys

Jakes-66-K10 · 10-07-2005, 12:47 PM

Larry, it was just built about 6 or 7 weeks ago. Bored .020 with dished pistons, stock crank, 5.7 rods, Comp Cams XE274, Vortec heads. Heads are bolted on, but I was planning on taking them off and machining in more lift for this cam. It's all complete with balancer and flexplate (both balanced for the 400) and an Edelbrock RPM intake. I'd sell it for $2k, also have a new TH400 short shaft tranny built to handle this motor and an oversized aluminum driveshaft - probably like $2600 for the entire drivetrain. If that's too steep no worries, my 66 keeps grinning at me knowing what it'll have thrown into it someday.

gmchevy · 10-12-2005, 09:26 PM

Hi Larry, I have a 88 s-10 blazer (daily driver) with a 400 small block...30 over, mild cam, edelbrock carb/manifold. $1500.00 if interested. I'm in Wichita Kansas.

69Goody · 10-12-2005, 11:32 PM

Hey Larry...Sounds like a good combo. That's pretty much what I have under my 69 GMC. A stout 400 bored .030, Edelbrock RPM heads, airgap manifold, crane gold rockers (1.6) motivated by a solid cam and connected to a posi 3.73 with new Moser axles. 5 on 5's all around compliments of a 78 doner. The only thing I'd do differently is stay away from the solid cam. Sounds good when valve train stays in place...go hydraulic.
Good luck and welcom back!

Larry68GMC · 10-14-2005, 12:59 AM

gmchevy, you got a PM about the blazer..thanks

Larry68GMC · 10-20-2005, 05:55 PM

Still looking for this stuff. Did you get my message gmchevy? Thanks...

David Johnson · 10-20-2005, 06:38 PM

Larry,
I have a 4 bolt 400 (hard to find), crank and balancer. I'm just down the road in Tecumseh. $500

RicksTrucks · 10-20-2005, 07:48 PM

I am picking up a 70 LWB tomorrow with a BB 400, may end up parting it out. It is all there: power steering and A/C with all of the brackets.

Larry68GMC · 10-21-2005, 09:37 AM

David and Rick, can you guys get some pics and casting numbers? How much you wanting for the BB 400 and all the brackets, motor mounts, etc Rick? Thanks...Larry

10-06-2005, 03:13 PM	#1
Larry68GMC Registered User Join Date: Aug 2001 Location: Midwest City, OK Posts: 289	WTB: SB 400 and rear end Just got back from Iraq and looking for a complete SB 400, would be interested in just the long block as well, within a few hours of Oklahoma City. Also a 3:73 or 4:10 5 lug posi with leafs...Thanks...Larry __________________ 71 GMC LWB 350, Dart Pro1's 200/64cc,10.2:1 RPM AirGap, 224/234 @50 496/518 lift w/1.6 roller rockers, 2500 stall '05 Dodge 2500 Crew Cab 4x4, 4 inch lift and 35's CTD

10-07-2005, 11:20 AM	#5
Larry68GMC Registered User Join Date: Aug 2001 Location: Midwest City, OK Posts: 289	Thanks for the info cst70, How much you asking and what are the specs Vortex? Thanks...guys __________________ 71 GMC LWB 350, Dart Pro1's 200/64cc,10.2:1 RPM AirGap, 224/234 @50 496/518 lift w/1.6 roller rockers, 2500 stall '05 Dodge 2500 Crew Cab 4x4, 4 inch lift and 35's CTD

10-07-2005, 12:47 PM	#6
Jakes-66-K10 Registered User Join Date: Aug 2004 Location: Idaho Posts: 640	Larry, it was just built about 6 or 7 weeks ago. Bored .020 with dished pistons, stock crank, 5.7 rods, Comp Cams XE274, Vortec heads. Heads are bolted on, but I was planning on taking them off and machining in more lift for this cam. It's all complete with balancer and flexplate (both balanced for the 400) and an Edelbrock RPM intake. I'd sell it for $2k, also have a new TH400 short shaft tranny built to handle this motor and an oversized aluminum driveshaft - probably like $2600 for the entire drivetrain. If that's too steep no worries, my 66 keeps grinning at me knowing what it'll have thrown into it someday. Attached Images

10-12-2005, 09:26 PM	#7
gmchevy Registered User Join Date: Feb 2003 Location: Wichita Kansas Posts: 15	s-10 v8 (400/350) Hi Larry, I have a 88 s-10 blazer (daily driver) with a 400 small block...30 over, mild cam, edelbrock carb/manifold. $1500.00 if interested. I'm in Wichita Kansas. __________________ 68 GMC shortbed 72 Chevy K5 Blazer CST 72 Chevy half ton 4X4 72 Chevy swb 4x4

10-12-2005, 11:32 PM	#8
69Goody Registered User Join Date: Jul 2004 Location: Southern Tip of OHIO 45680 Posts: 49	Hey Larry...Sounds like a good combo. That's pretty much what I have under my 69 GMC. A stout 400 bored .030, Edelbrock RPM heads, airgap manifold, crane gold rockers (1.6) motivated by a solid cam and connected to a posi 3.73 with new Moser axles. 5 on 5's all around compliments of a 78 doner. The only thing I'd do differently is stay away from the solid cam. Sounds good when valve train stays in place...go hydraulic. Good luck and welcom back! __________________ Only the Mediocre are always at their best... '69 GMC LWB 406, TH400, 3.73 Posi' Things I've learned from my truck...If I was an automaker, my vehicles would be overpriced, run rough, and get 5MPG.

10-06-2005, 03:30 PM	#2
Jakes-66-K10 Registered User Join Date: Aug 2004 Location: Idaho Posts: 640	How much you looking to spend? I have a built one with vortec heads with intake manifold I was going to use on my '66... but it's just sitting around doing nothing for about 6 weeks now.

10-06-2005, 03:35 PM	#3
cst70rocket Registered User Join Date: Sep 2005 Location: San Angelo or Eufaula Posts: 301	Larry, there is a guy in Wichita Falls,Tx with a stock 400 short block, never been torn down, standard bore. He is asking $300 for it and you pick it up. Very nice guy. I just bought the rotating assy from him. His name is Scott Schultz, his number is 940-631-5865 You can tell him that Kirk from San Angelo sent ya. Kirk

10-06-2005, 03:38 PM	#4
cst70rocket Registered User Join Date: Sep 2005 Location: San Angelo or Eufaula Posts: 301	I may also have a buddy with a later model 10 bolt with fresh posi,new 3.73 gears and new brakes/drums if he still has it, he was asking $500 for it. It's leaf sprung, and I believe it's a bolt in, but don't quote me on that. If interested, email me. cst70rocket@yahoo.com Kirk

10-14-2005, 12:59 AM	#9
Larry68GMC Registered User Join Date: Aug 2001 Location: Midwest City, OK Posts: 289	gmchevy, you got a PM about the blazer..thanks __________________ 71 GMC LWB 350, Dart Pro1's 200/64cc,10.2:1 RPM AirGap, 224/234 @50 496/518 lift w/1.6 roller rockers, 2500 stall '05 Dodge 2500 Crew Cab 4x4, 4 inch lift and 35's CTD

10-20-2005, 05:55 PM	#10
Larry68GMC Registered User Join Date: Aug 2001 Location: Midwest City, OK Posts: 289	Re: WTB: SB 400 and rear end Still looking for this stuff. Did you get my message gmchevy? Thanks... __________________ 71 GMC LWB 350, Dart Pro1's 200/64cc,10.2:1 RPM AirGap, 224/234 @50 496/518 lift w/1.6 roller rockers, 2500 stall '05 Dodge 2500 Crew Cab 4x4, 4 inch lift and 35's CTD

10-20-2005, 06:38 PM	#11
David Johnson Registered User Join Date: Dec 2004 Location: Shawnee, OK Posts: 614	Re: WTB: SB 400 and rear end Larry, I have a 4 bolt 400 (hard to find), crank and balancer. I'm just down the road in Tecumseh. $500

10-20-2005, 07:48 PM	#12
RicksTrucks Senior Member Join Date: Jan 2005 Location: Claremore, OK 74017 Posts: 2,639	Re: WTB: SB 400 and rear end I am picking up a 70 LWB tomorrow with a BB 400, may end up parting it out. It is all there: power steering and A/C with all of the brackets. __________________ 68 Short Stepside C-10 69 SWB C-10 70 Flatbed C-20 70 LWB C-20 BB402 70 LWB C-10 CST 70 LWB C-10 CST 71 Short Stepside Cheyenne C-10 72 LWB C-10 72 Blazer 4x4 4spd 95 Jeep Cherokee 4x4

10-21-2005, 09:37 AM	#13
Larry68GMC Registered User Join Date: Aug 2001 Location: Midwest City, OK Posts: 289	Re: WTB: SB 400 and rear end David and Rick, can you guys get some pics and casting numbers? How much you wanting for the BB 400 and all the brackets, motor mounts, etc Rick? Thanks...Larry __________________ 71 GMC LWB 350, Dart Pro1's 200/64cc,10.2:1 RPM AirGap, 224/234 @50 496/518 lift w/1.6 roller rockers, 2500 stall '05 Dodge 2500 Crew Cab 4x4, 4 inch lift and 35's CTD



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.