|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
10-30-2005, 04:52 PM
|
#1 |
|
Registered User
Join Date: Jan 2002
Location: Slippery Rock PA USA
Posts: 1,692
|
anybody running a crane xr-1 conversion?
...anybody running a crane cams xr-1 electronic ignition conversion?..just wondered if anyone had any problems with it.....seems like a cheap way to go with a rev limiter...thanks.....
__________________
Ken Lyons, Slippery rock pa 68 short step 327 t10 4 gear 72 2wd blazer project 70 lwb 305/700r driver 78 caprice project 02 cavalier D.D ( hate it!!) |
|
|
|
10-31-2005, 07:14 PM
|
#2 |
|
Registered User
Join Date: Jan 2002
Location: Slippery Rock PA USA
Posts: 1,692
|
Re: anybody running a crane xr-1 conversion?
.............i'll take that as a no............lol..........
__________________
Ken Lyons, Slippery rock pa 68 short step 327 t10 4 gear 72 2wd blazer project 70 lwb 305/700r driver 78 caprice project 02 cavalier D.D ( hate it!!) |
|
|
|
|
10-31-2005, 07:34 PM
|
#3 |
|
Active Member
Join Date: Jul 2003
Location: Boise Idaho
Posts: 296
|
Re: anybody running a crane xr-1 conversion?
Like you, I though it looked like a pretty slick deal with the rev limiter and all. I bought one, but never installed it....went with hei instead. So I can't tell you how well it works.
__________________
1971 SWB SOLD
|
|
|
|
|
10-31-2005, 07:56 PM
|
#4 |
|
Registered User
Join Date: Aug 2001
Location: Jesup, GA
Posts: 571
|
Re: anybody running a crane xr-1 conversion?
A friend of mine is running one on his 72 Corvette. He is very happy with it. The rev limiter works good.
|
|
|
|
|
10-31-2005, 08:25 PM
|
#5 |
|
Registered User
Join Date: Nov 2003
Location: Alexandria, VA
Posts: 1,534
|
Re: anybody running a crane xr-1 conversion?
I thought about buying the Crane xr-1 kit, but my distributor needs new bushings, advance canister and and the mech. advance curve reset for the 383. Anyone know where I can buy the distributor main shaft bushings?
__________________
'72 GMC SWB C1500 Custom, frame-off in progress. 383 SBC, 9:1CR, Comp Cams XE262H, Scat internal balanced crank, Eagle SIR 6" rods, Keith Black dish pistons, Dart Iron Eagle 72/180 heads, Weiand Stealth intake, Stewart stage I water pump, Holley 4bbl vac sec, TH350 with B&M Shift Improver Kit. 12 bolt positraction.   
|
|
|
|
|
10-31-2005, 08:27 PM
|
#6 | |
|
Registered User
Join Date: Nov 2003
Location: Alexandria, VA
Posts: 1,534
|
Re: anybody running a crane xr-1 conversion?
Quote:
 Don't mean to hijack your thread mooneyes4b.
__________________
'72 GMC SWB C1500 Custom, frame-off in progress. 383 SBC, 9:1CR, Comp Cams XE262H, Scat internal balanced crank, Eagle SIR 6" rods, Keith Black dish pistons, Dart Iron Eagle 72/180 heads, Weiand Stealth intake, Stewart stage I water pump, Holley 4bbl vac sec, TH350 with B&M Shift Improver Kit. 12 bolt positraction.
Last edited by Sweet72; 10-31-2005 at 08:30 PM. |
|
|
|
|
|
10-31-2005, 08:59 PM
|
#7 | |
|
Active Member
Join Date: Jul 2003
Location: Boise Idaho
Posts: 296
|
Re: anybody running a crane xr-1 conversion?
Quote:
 (I still have it sitting out in the garage)!!
__________________
1971 SWB SOLD
|
|
|
|
|
|
11-01-2005, 07:43 PM
|
#8 |
|
Registered User
Join Date: Jan 2002
Location: Slippery Rock PA USA
Posts: 1,692
|
Re: anybody running a crane xr-1 conversion?
......thanks guys...i usually always go with hei..cheap and simple...but i think i might try the crane set up...thanks again
__________________
Ken Lyons, Slippery rock pa 68 short step 327 t10 4 gear 72 2wd blazer project 70 lwb 305/700r driver 78 caprice project 02 cavalier D.D ( hate it!!) |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
