11-25-2005, 03:12 AM | #1 |
Designated A-hole!
Join Date: Mar 2003
Location: South Mississippi
Posts: 36,448
|
What's it called?
I need to stop a leak between the tranny and xfer case of my 72 Blazer. It's a th350 tranny (I think) with a 205 xfer case (again I think). What do I need to tell the parts guy I need?
__________________
"If it ain't broke, fix it 'til it is!" Being stupid ain't illegal. We're Still Debt Free Except for the House!!! www.daveramsey.com 70 GMC SWB Stepside project "Green Booger" soon to be 6.0l/4l80e 93 S-10 "Poppaw's Truck" |
11-25-2005, 06:00 AM | #2 |
user # 2756
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
Re: What's it called?
output seal of the tranny and an input seal for the transfercase.
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm |
11-25-2005, 08:51 PM | #3 |
Registered User
Join Date: Dec 2003
Location: West Michigan
Posts: 447
|
Re: What's it called?
Is it leaking tranny fluid into the transfer case?
__________________
1972 Chevy Blazer 1997 GMC Sierra 2009 Chevy Tahoe |
11-26-2005, 04:32 AM | #4 |
Senior Member
Join Date: Jan 2003
Location: Grand Junction, Colorado
Posts: 610
|
Re: What's it called?
Since you will have the tcase on the ground...the adapter has two seals inside it to seal the trans from the xfer. Being a gen1 K5...assuming things haven't been swapped around the coupler will have a large bearing on it...the seals point inwards. Make sure the coupler splines are not worn out. You'll need a rubber square cut oring that seals the back of the th350 to the adapter...and if you do the coupler seals which i highly recommend...you'll also need the paper gasket that mounts the xfer to the adapter...so that would be a total of 4 seals to do it right.
DW
__________________
Doug Wright aka K5NUTT over @coloradok5.com Owner of http://groups.yahoo.com/group/ChevyK5BlazerChalets Certified K5 Nut |
11-26-2005, 11:59 PM | #5 |
Designated A-hole!
Join Date: Mar 2003
Location: South Mississippi
Posts: 36,448
|
Re: What's it called?
Thanks guys.
__________________
"If it ain't broke, fix it 'til it is!" Being stupid ain't illegal. We're Still Debt Free Except for the House!!! www.daveramsey.com 70 GMC SWB Stepside project "Green Booger" soon to be 6.0l/4l80e 93 S-10 "Poppaw's Truck" |
Bookmarks |
|
|