Tranny Swap help - The 1947 - Present Chevrolet & GMC Truck Message Board Network

bballmac42 · 12-16-2005, 09:50 AM

I am looking to swap the tranny in my truck. i have a 3 speed on the column and would like to go the four speed on the florr route. any one done this and have any insight? also, anyone know what a good 4 speed would be and where i could find one/

**Yukon Jack** · 12-16-2005, 10:50 AM

How do you use the truck? The SM465 4 speed is good and tough. Has the granny 1st gear and is pretty plentiful. Is your truck a 2wd or 4wd. That will matter when picking the tranny. You ought to be able to find these at your local junk yard.

I was told that the bellhousing hole for the three speed tranny is slightly differnet sized than the bellhousing hole for the 4 speed tranny - I have never confirmed this so you need to figure that out to see if you need a different bellhousing.

Unless you know the age and condition of your clutch, might as well throw a new one in when you do the tranny swap.

crazy longhorn · 12-16-2005, 12:03 PM

Bell housing hole sizes.....67 & older were 4 11/16"(same as car). the 68 - up got a 5 1/8" hole on the trucks. you will also need a high hump floor cover to run the 4spd truck trans. best of luck,crazyL

bballmac42 · 12-16-2005, 06:47 PM

its a 2 wheel drive truck. i was actually thinking of that tranny yukon, but am not sure where to get my hands on one.

12-16-2005, 09:50 AM	#1
bballmac42 Registered User Join Date: Aug 2005 Location: Wisconsin Posts: 60	Tranny Swap help I am looking to swap the tranny in my truck. i have a 3 speed on the column and would like to go the four speed on the florr route. any one done this and have any insight? also, anyone know what a good 4 speed would be and where i could find one/

12-16-2005, 10:50 AM	#2
Yukon Jack Post Whore Join Date: Feb 2000 Location: Rose Hill, KS, USA Posts: 12,684	Re: Tranny Swap help How do you use the truck? The SM465 4 speed is good and tough. Has the granny 1st gear and is pretty plentiful. Is your truck a 2wd or 4wd. That will matter when picking the tranny. You ought to be able to find these at your local junk yard. I was told that the bellhousing hole for the three speed tranny is slightly differnet sized than the bellhousing hole for the 4 speed tranny - I have never confirmed this so you need to figure that out to see if you need a different bellhousing. Unless you know the age and condition of your clutch, might as well throw a new one in when you do the tranny swap. __________________ 1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14

12-16-2005, 12:03 PM	#3
crazy longhorn Fabricate till you "puke" Join Date: Jun 2002 Location: Ill Posts: 9,403	Re: Tranny Swap help Bell housing hole sizes.....67 & older were 4 11/16"(same as car). the 68 - up got a 5 1/8" hole on the trucks. you will also need a high hump floor cover to run the 4spd truck trans. best of luck,crazyL __________________ 69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears....

12-16-2005, 06:47 PM	#4
bballmac42 Registered User Join Date: Aug 2005 Location: Wisconsin Posts: 60	Re: Tranny Swap help its a 2 wheel drive truck. i was actually thinking of that tranny yukon, but am not sure where to get my hands on one.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.