Did the trick guys!!!!!!1 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

84 400 · 01-14-2006, 11:02 PM

Well as was suggested by some of yall i ended up changing my rear dif fluid in my 85 beater c10/daily driver / project truck. any ways it now has no poopping comming from the rear end when i turn the wheel. allso it doesn't stall in revease. This was a real help i think . any ways it was real brown looking and kind of mucky but not burnt black. i did however have one bolt go down in the prossess. it was on the diff cover and on the passanger side two up from the bottom so now i have a chevy 9.5 bolt. I don't have the tools to drill it out so now it only has 9 bolt heads on it is this going to bite me in the but??? it is kind of funny cause at school on thursday we were doing a change on there truck and replacing the leaky seals and the same bolt snapped. when the drill it out i will see if i can barrow the tool for the weekend and fix mine. but thanks again

pebbleboy · 01-14-2006, 11:32 PM

e z outs are only like 5 bucks at autozone.

Had to buy one recently.

crazyred · 01-15-2006, 04:05 AM

a small chisel and a hammer to spin it out ... that is if it's not broke too deep in there..... or weld a nut onto the broken part, let it cool good, and try and spin-er-out ...Thats what i always do!!!

01-14-2006, 11:02 PM	#1
84 400 Sb 400 club Join Date: Nov 2005 Location: NH / MA Posts: 2,746	Did the trick guys!!!!!!1 Well as was suggested by some of yall i ended up changing my rear dif fluid in my 85 beater c10/daily driver / project truck. any ways it now has no poopping comming from the rear end when i turn the wheel. allso it doesn't stall in revease. This was a real help i think . any ways it was real brown looking and kind of mucky but not burnt black. i did however have one bolt go down in the prossess. it was on the diff cover and on the passanger side two up from the bottom so now i have a chevy 9.5 bolt. I don't have the tools to drill it out so now it only has 9 bolt heads on it is this going to bite me in the but??? it is kind of funny cause at school on thursday we were doing a change on there truck and replacing the leaky seals and the same bolt snapped. when the drill it out i will see if i can barrow the tool for the weekend and fix mine. but thanks again __________________ 1984 chevy c10, built 400sb,.(SOLD) 77 K10 Project / daily driver "The Grinch" http://67-72chevytrucks.com/vboard/s...d.php?t=318363 1956 Willys Wagon (327 chevy) Project (Now Buick 225) 1980 Corvette L-48 4 speed 1992 Mustang GT built 5.0 5 speed 1985 C10 LWB Sold 1982 K10 SWB plow truck Parted out 1986 D30 M1028 fire brush truck Parted out

01-15-2006, 04:05 AM	#3
crazyred yeeha Join Date: Sep 2005 Location: Sherwood Park & Fort McMurray, Alberta Posts: 72	Re: Did the trick guys!!!!!!1 a small chisel and a hammer to spin it out ... that is if it's not broke too deep in there..... or weld a nut onto the broken part, let it cool good, and try and spin-er-out ...Thats what i always do!!! __________________ 1969 GMC 910 97% rust free 2002 olds Alero 1986 New Yorker 4dr ... the new DD...My POS car... dude its got a turbo!!! Don't drink and drive, you might spill something!!! Daryl Kuchmak



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.