Transfer Case Swap Questions. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**special-K** · 01-25-2006, 08:33 PM

I have a`90 Blazer with a 4spd manual/NP241 combo.Would I be able to swap in a t-case from an`86 Blazer that had the 700r4/NP203?Was it a 203 in`86?I`m selling the`90 and I really want to keep the NP241/RH for a mate to a NV4500 I have.That`ll be going in a`72 with the 4spd/NP205 and I`d consider swapping that combo into the`90 or just use the 205 if that`s doeable.I can get the`86 combo and would like to have the 700r4,don`t care about the t-case.Any suggestions?

1967k30 · 01-26-2006, 12:33 AM

86' Blazer would have a 208'.They ran 203's from 71'-79' and never behind a 700r4. It would be easiest to swap the 465/205 in since it already has a stick.You will also need different driveshafts.

**special-K** · 01-26-2006, 09:50 AM

Thanks,I couldn`t remember which came first with the 203 & 208.I`ve newer had much use for either.So,I couldn`t bolt the 208 to the manual in the`90?This Blazer needs a clutch and it`s going as is(local/not on the board).I could sell it with the trans/t-case installed.

1967k30 · 01-26-2006, 10:45 AM

I hadn't thought of that.

Yes you could just swap the 208 onto the 90'465.Should bolt right up because they both have the round pattern.

**special-K** · 01-26-2006, 12:21 PM

Thanks,that`s what I wanna hear.Do you know a good place to look for a NV4500 case?I have one from a wreck w/15,000 miles and a broken corner at the front mounting surface.The piece is long gone.I have the 241/RH,same miles,frome the same truck.I`d get a Ford axle,but I have two sets of D60/14-bolts already.

01-25-2006, 08:33 PM	#1
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Transfer Case Swap Questions. I have a`90 Blazer with a 4spd manual/NP241 combo.Would I be able to swap in a t-case from an`86 Blazer that had the 700r4/NP203?Was it a 203 in`86?I`m selling the`90 and I really want to keep the NP241/RH for a mate to a NV4500 I have.That`ll be going in a`72 with the 4spd/NP205 and I`d consider swapping that combo into the`90 or just use the 205 if that`s doeable.I can get the`86 combo and would like to have the 700r4,don`t care about the t-case.Any suggestions? __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

01-26-2006, 12:33 AM	#2
1967k30 Senior Member Join Date: Sep 2005 Location: NE Posts: 363	Re: Transfer Case Swap Questions. 86' Blazer would have a 208'.They ran 203's from 71'-79' and never behind a 700r4. It would be easiest to swap the 465/205 in since it already has a stick.You will also need different driveshafts. __________________ 01 2500 Duramax,6spd,4x4,Not stock. Estimated 550rwhp/1100rwfp on fuel only. 03 3500 Duramax,6spd,4x4,Pac-Brake,not stock Estimated 500rwhp/1000rwfp fuel only 67 K10 in many pieces Little Brothers truck 67 K20 Cummins 12V/NV4500/205, D60/Eaton w/ Detroit,37" Xterrains,crossover steering, Future plans,Twins and lots of fuel.

01-26-2006, 09:50 AM	#3
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: Transfer Case Swap Questions. Thanks,I couldn`t remember which came first with the 203 & 208.I`ve newer had much use for either.So,I couldn`t bolt the 208 to the manual in the`90?This Blazer needs a clutch and it`s going as is(local/not on the board).I could sell it with the trans/t-case installed. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

01-26-2006, 10:45 AM	#4
1967k30 Senior Member Join Date: Sep 2005 Location: NE Posts: 363	Re: Transfer Case Swap Questions. I hadn't thought of that. Yes you could just swap the 208 onto the 90'465.Should bolt right up because they both have the round pattern. __________________ 01 2500 Duramax,6spd,4x4,Not stock. Estimated 550rwhp/1100rwfp on fuel only. 03 3500 Duramax,6spd,4x4,Pac-Brake,not stock Estimated 500rwhp/1000rwfp fuel only 67 K10 in many pieces Little Brothers truck 67 K20 Cummins 12V/NV4500/205, D60/Eaton w/ Detroit,37" Xterrains,crossover steering, Future plans,Twins and lots of fuel.

01-26-2006, 12:21 PM	#5
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: Transfer Case Swap Questions. Thanks,that`s what I wanna hear.Do you know a good place to look for a NV4500 case?I have one from a wreck w/15,000 miles and a broken corner at the front mounting surface.The piece is long gone.I have the 241/RH,same miles,frome the same truck.I`d get a Ford axle,but I have two sets of D60/14-bolts already. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.