Need some exhaust pics - The 1947 - Present Chevrolet & GMC Truck Message Board Network

70c10 · 02-23-2006, 08:11 AM

The more I look at my exhaust, the more I don't like it. Does anybody have any pics of Full length headers (Not shorties or ramhorns) with a nice tucked up exhaust??. I want to shorten mine again to exit in front of the rear tires. Thanks

68jimmy · 02-23-2006, 09:37 AM

Try this. http://67-72chevytrucks.com/vboard/s...d.php?t=187968

It has quite a few good ideas...

good luck.

70c10 · 02-23-2006, 10:18 AM

That's a beautiful job but he retained stock manifolds. I was hoping to see pics using full length headers like I have. Thanks

speedracer · 02-23-2006, 01:56 PM

most full length headers hang down past the frame I had to use 3/4 length.

70rs/ss · 02-23-2006, 02:51 PM

The best you can do with full length is a little below the frame. I ran mine straight back to where the frame starts to turn up over the rear axle and jumped the pipes outside the frame there and up and over the axle and out the back. this works great for a lowered truck. I have no picts though. If I had it to do all over again I'd get the shorty Chevelle headers and run the rest of the exhaust the way I mentioned above and the pipes will be out of sight and and out on mind!

Frizzle Fry · 02-23-2006, 03:35 PM

It's a Suburban, but it's what you're describing:

70c10 · 02-23-2006, 04:47 PM

Thanks Mike. Your mufflers look a little higher off the ground than mine so there is hope!

70c10 · 02-25-2006, 11:48 AM

Anybody else have some pics of exhaust with Full length headers?.

02-23-2006, 08:11 AM	#1
70c10 67-72 Addict! Join Date: Feb 2002 Location: The TAX State! Posts: 7,856	Need some exhaust pics The more I look at my exhaust, the more I don't like it. Does anybody have any pics of Full length headers (Not shorties or ramhorns) with a nice tucked up exhaust??. I want to shorten mine again to exit in front of the rear tires. Thanks __________________ Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads

02-23-2006, 09:37 AM	#2
68jimmy Registered User Join Date: Dec 2003 Location: albuquerque Posts: 431	Re: Need some exhaust pics Try this. http://67-72chevytrucks.com/vboard/s...d.php?t=187968 It has quite a few good ideas... good luck. __________________ 78 C10 LWB Super Cheyenne

02-23-2006, 10:18 AM	#3
70c10 67-72 Addict! Join Date: Feb 2002 Location: The TAX State! Posts: 7,856	Re: Need some exhaust pics That's a beautiful job but he retained stock manifolds. I was hoping to see pics using full length headers like I have. Thanks __________________ Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads

02-23-2006, 01:56 PM	#4
speedracer Blank Join Date: May 2005 Location: Southington, CT Posts: 221	Re: Need some exhaust pics most full length headers hang down past the frame I had to use 3/4 length. __________________ 1969 lwb 4/6 drop 17x8-18x10 torque thrust II's 327-420hp 2004R 3.73 posi. 1977 Corvette 350-375hp 4speed, silver show car. 2002 S10 xtreme, work truck 2004.5 VW jetta GLI 1.8T 6speed, weekend warrior. 2013 Audi A3 TDI, the wife's car

02-23-2006, 02:51 PM	#5
70rs/ss Registered User Join Date: Dec 2004 Location: Northern AZ Posts: 7,270	Re: Need some exhaust pics The best you can do with full length is a little below the frame. I ran mine straight back to where the frame starts to turn up over the rear axle and jumped the pipes outside the frame there and up and over the axle and out the back. this works great for a lowered truck. I have no picts though. If I had it to do all over again I'd get the shorty Chevelle headers and run the rest of the exhaust the way I mentioned above and the pipes will be out of sight and and out on mind!

02-23-2006, 03:35 PM	#6
Frizzle Fry Registered User Join Date: Aug 2005 Location: Hillsboro Oregon Posts: 6,449	Re: Need some exhaust pics It's a Suburban, but it's what you're describing: Attached Images

02-23-2006, 04:47 PM	#7
70c10 67-72 Addict! Join Date: Feb 2002 Location: The TAX State! Posts: 7,856	Re: Need some exhaust pics Thanks Mike. Your mufflers look a little higher off the ground than mine so there is hope! __________________ Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads

02-25-2006, 11:48 AM	#8
70c10 67-72 Addict! Join Date: Feb 2002 Location: The TAX State! Posts: 7,856	Re: Need some exhaust pics Anybody else have some pics of exhaust with Full length headers?. __________________ Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.