Van tilt -- hazards - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**dennislbrooks** · 03-15-2006, 10:44 AM

I may have seen this on here before but after a successful install of my van tilt in my 67, everything works but the hazard lights. When I push it in --nothing happens. I used the adapter plug from the flat to the half moon. What do I need to do or what should I check?

Bob Moore · 03-15-2006, 01:01 PM

Dennis - I have not heard of this before. The obvious would be the flasher unit. The only other thing I can think of is a bad turnsignal. If the blinkers work left and right you can rule out the adapter.

Keep us posted - Bob

**dennislbrooks** · 03-15-2006, 01:55 PM

Thanks Bob, turn signals work OK---definitely may be the hazard flasher as I cannot ever remember trying it before the column change--- they must not check it at the yearly inspections.

**dennislbrooks** · 03-18-2006, 11:07 PM

Replaced the hazard flasher, checked the fuse and made sure power to both sides of fuse with ignition key off. Hazard flashers still do not work. I have power to the hazaed flasher unit all the time so the connection may not be made somewhere else when I push the flasher switch in. Both turn signals work ok with the key on. Am having trouble making out the wiring diagram on them. I do not think they worked before I switched to the tilt from the 67 oem.

Longhorn Man · 03-19-2006, 10:31 AM

I would set the old column in the truck on the floor, and plug it in. Try the 4 ways from the old column and if they work, you know you have a bum switch. Knowing the way they work... it's pretty much going to be a bum switch anyways.

03-15-2006, 10:44 AM	#1
dennislbrooks Senior Member Join Date: Feb 2004 Location: Williamsburg, Ohio Posts: 1,766	Van tilt -- hazards I may have seen this on here before but after a successful install of my van tilt in my 67, everything works but the hazard lights. When I push it in --nothing happens. I used the adapter plug from the flat to the half moon. What do I need to do or what should I check?

03-15-2006, 01:01 PM	#2
Bob Moore Registered User Join Date: Feb 2004 Location: Tacoma WA Posts: 1,365	Re: Van tilt -- hazards Dennis - I have not heard of this before. The obvious would be the flasher unit. The only other thing I can think of is a bad turnsignal. If the blinkers work left and right you can rule out the adapter. Keep us posted - Bob __________________ 67 C-20 LWB, tilt, speed alert, vac, 454, T400 67 C-10 SWB, factory air with more to follow

03-15-2006, 01:55 PM	#3
dennislbrooks Senior Member Join Date: Feb 2004 Location: Williamsburg, Ohio Posts: 1,766	Re: Van tilt -- hazards Thanks Bob, turn signals work OK---definitely may be the hazard flasher as I cannot ever remember trying it before the column change--- they must not check it at the yearly inspections.

03-18-2006, 11:07 PM	#4
dennislbrooks Senior Member Join Date: Feb 2004 Location: Williamsburg, Ohio Posts: 1,766	Re: Van tilt -- hazards Replaced the hazard flasher, checked the fuse and made sure power to both sides of fuse with ignition key off. Hazard flashers still do not work. I have power to the hazaed flasher unit all the time so the connection may not be made somewhere else when I push the flasher switch in. Both turn signals work ok with the key on. Am having trouble making out the wiring diagram on them. I do not think they worked before I switched to the tilt from the 67 oem. Last edited by dennislbrooks; 03-18-2006 at 11:15 PM.

03-19-2006, 10:31 AM	#5
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	Re: Van tilt -- hazards I would set the old column in the truck on the floor, and plug it in. Try the 4 ways from the old column and if they work, you know you have a bum switch. Knowing the way they work... it's pretty much going to be a bum switch anyways.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.