WTB parts to finish project! - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Als454 · 05-03-2006, 07:57 PM

Just finishing for parts before turning to a vendor. I need the following:

Right front fender for 72
Rear cross sill (wood bed)
Front bed panel(wood bed)
Wheel housings
P/S remote resevoir for big block

Also need the spring that is in the automatic Column (tilt) for the gear shift
Lost mine somewhere along the line. Does anyone know if this is the same spring as in the non-tilt column?

Thanks Allen.

greenhorn male · 05-03-2006, 08:12 PM

I may have the spring/s for the auto tilt, if you or someone can post a pic of this thing.

Als454 · 05-03-2006, 09:21 PM

Greenhorn, I don't have a picture. All I have is a distant memory of what it looked like before I lost it. Maybe someone else can come up with a picture.
Allen

greenhorn male · 05-03-2006, 10:27 PM

Al, tell me if this is the spring. All the other little parts are also off a tilt.

71SWBChevy · 05-03-2006, 10:29 PM

the front panel you need for fleet or step?

Als454 · 05-04-2006, 06:37 PM

Greenhorn, I believe that is the tilt spring, that one I have. The one I am missing is for the gear shift and is much smaller.

Als454 · 05-04-2006, 06:38 PM

71SWBCHEVY, the panel would be for a fleet side.

greenhorn male · 05-04-2006, 07:53 PM

Is it these springs inside the housing?

Hotrodhenryj · 05-04-2006, 11:09 PM

Allen, I have one nice wheel housing and the BB reservoir. Both for $50 shipped. Chuck

Bob Moore · 05-04-2006, 11:22 PM

I have the tilt spring from inside the shift bowl. $6.50 to your door.

I can PM you my mailing address. Thanks - Bob

Als454 · 05-05-2006, 09:46 PM

Hey Guys, Let me try to describe this spring a little better. It is the one that goes with the gear shift (selector lever). It is located under the very end of the lever where it extends into the column. When you pull the gear shift toward you to release it (shift) you are pulling against this spring.
Allen

Bob Moore · 05-07-2006, 12:10 AM

Yes Allen, that is the one I can ship to your door for $6.50. 5/16 diameter by 7/8 long. It goes under the shift lever to provide tension putting the lever into the detent gate to prevent slipping out of Park and reverse without pulling on the lever.

Let me know - Bob

05-03-2006, 07:57 PM	#1
Als454 Senior Member Join Date: Jan 2002 Location: Vienna, Ohio, USA Posts: 259	WTB parts to finish project! Just finishing for parts before turning to a vendor. I need the following: Right front fender for 72 Rear cross sill (wood bed) Front bed panel(wood bed) Wheel housings P/S remote resevoir for big block Also need the spring that is in the automatic Column (tilt) for the gear shift Lost mine somewhere along the line. Does anyone know if this is the same spring as in the non-tilt column? Thanks Allen. __________________ 72 Chevy A/C P/B P/S Tilt 454 Engine 400 TCI Trans C30 Frame C10 Suspension Short Wheel Base (Dually)

05-03-2006, 08:12 PM	#2
greenhorn male Senior Member Join Date: Jan 2003 Location: Bay Area, Northern California Posts: 1,344	Re: WTB parts to finish project! I may have the spring/s for the auto tilt, if you or someone can post a pic of this thing. __________________ 03 Tahoe 72 GMC Super Custom 2500 Custom Camper, my reliable workhorse. Dual gauged tanks, dual battery trays.

05-03-2006, 09:21 PM	#3
Als454 Senior Member Join Date: Jan 2002 Location: Vienna, Ohio, USA Posts: 259	Re: WTB parts to finish project! Greenhorn, I don't have a picture. All I have is a distant memory of what it looked like before I lost it. Maybe someone else can come up with a picture. Allen __________________ 72 Chevy A/C P/B P/S Tilt 454 Engine 400 TCI Trans C30 Frame C10 Suspension Short Wheel Base (Dually)

05-03-2006, 10:27 PM	#4
greenhorn male Senior Member Join Date: Jan 2003 Location: Bay Area, Northern California Posts: 1,344	Re: WTB parts to finish project! Al, tell me if this is the spring. All the other little parts are also off a tilt. Attached Images __________________ 03 Tahoe 72 GMC Super Custom 2500 Custom Camper, my reliable workhorse. Dual gauged tanks, dual battery trays.

05-03-2006, 10:29 PM	#5
71SWBChevy Post Whore Join Date: Aug 2005 Location: Owensboro KY Posts: 11,905	Re: WTB parts to finish project! the front panel you need for fleet or step? __________________ Drew '71 Chevy 350/TH350 Hugger Orange Currently just a rolling frame, body work soon to follow!!! Check out my Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=212927 Daily Driver: 1997 Chevrolet S-10 with more gears than pistons

05-04-2006, 06:37 PM	#6
Als454 Senior Member Join Date: Jan 2002 Location: Vienna, Ohio, USA Posts: 259	Re: WTB parts to finish project! Greenhorn, I believe that is the tilt spring, that one I have. The one I am missing is for the gear shift and is much smaller. __________________ 72 Chevy A/C P/B P/S Tilt 454 Engine 400 TCI Trans C30 Frame C10 Suspension Short Wheel Base (Dually)

05-04-2006, 06:38 PM	#7
Als454 Senior Member Join Date: Jan 2002 Location: Vienna, Ohio, USA Posts: 259	Re: WTB parts to finish project! 71SWBCHEVY, the panel would be for a fleet side. __________________ 72 Chevy A/C P/B P/S Tilt 454 Engine 400 TCI Trans C30 Frame C10 Suspension Short Wheel Base (Dually)

05-04-2006, 07:53 PM	#8
greenhorn male Senior Member Join Date: Jan 2003 Location: Bay Area, Northern California Posts: 1,344	Re: WTB parts to finish project! Is it these springs inside the housing? __________________ 03 Tahoe 72 GMC Super Custom 2500 Custom Camper, my reliable workhorse. Dual gauged tanks, dual battery trays. Last edited by greenhorn male; 05-04-2006 at 07:55 PM.

05-04-2006, 11:09 PM	#9
Hotrodhenryj Truck Farmer Join Date: Nov 2001 Location: Lake Havasu City, Arizona Posts: 1,192	Re: WTB parts to finish project! Allen, I have one nice wheel housing and the BB reservoir. Both for $50 shipped. Chuck __________________ Arizona rust free sheetmetal

05-04-2006, 11:22 PM	#10
Bob Moore Registered User Join Date: Feb 2004 Location: Tacoma WA Posts: 1,365	Re: WTB parts to finish project! I have the tilt spring from inside the shift bowl. $6.50 to your door. I can PM you my mailing address. Thanks - Bob __________________ 67 C-20 LWB, tilt, speed alert, vac, 454, T400 67 C-10 SWB, factory air with more to follow

05-05-2006, 09:46 PM	#11
Als454 Senior Member Join Date: Jan 2002 Location: Vienna, Ohio, USA Posts: 259	Re: WTB parts to finish project! Hey Guys, Let me try to describe this spring a little better. It is the one that goes with the gear shift (selector lever). It is located under the very end of the lever where it extends into the column. When you pull the gear shift toward you to release it (shift) you are pulling against this spring. Allen __________________ 72 Chevy A/C P/B P/S Tilt 454 Engine 400 TCI Trans C30 Frame C10 Suspension Short Wheel Base (Dually)

05-07-2006, 12:10 AM	#12
Bob Moore Registered User Join Date: Feb 2004 Location: Tacoma WA Posts: 1,365	Re: WTB parts to finish project! Yes Allen, that is the one I can ship to your door for $6.50. 5/16 diameter by 7/8 long. It goes under the shift lever to provide tension putting the lever into the detent gate to prevent slipping out of Park and reverse without pulling on the lever. Let me know - Bob __________________ 67 C-20 LWB, tilt, speed alert, vac, 454, T400 67 C-10 SWB, factory air with more to follow



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.