throttle cable question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

speed · 05-10-2006, 04:56 PM

For those that changed out the throttle cable for a Lokar one, how did you mount it to the pedal. Pictures would be a plus too. TIA

79BIG10 · 05-11-2006, 04:02 AM

On mine the top part of the pedal's rod was worn out. I ended up engineering mine on with a new hole drilled out and used the kit it came with. But then I ran into an issue and used a clamp from Home Depot in the hardware section that tightens up aircraft cable. This kept it stronger than the little ball that it had came with.

But if you can take your old one out and replace the same way it went.

speed · 05-11-2006, 08:37 PM

I worked on it some today. cut the "cup" off an old throttle cable and slid it on the cable. Didn't use the end that was sent with the cable. Now to trim it to fit nicely.

**swervin ervin** · 05-11-2006, 09:15 PM

Speed,

that's what I did also.

bigfredtn · 05-16-2006, 05:12 PM

Can someone post a picture of the set up?

05-10-2006, 04:56 PM	#1
speed Junior Member Join Date: Jan 2006 Location: Northern Iowa Posts: 258	throttle cable question For those that changed out the throttle cable for a Lokar one, how did you mount it to the pedal. Pictures would be a plus too. TIA __________________ Jeff J ---------- 86 El Camino 81 Monte Carlo 81 Regal 04 Colorado

05-11-2006, 04:02 AM	#2
79BIG10 I'm back with 2nd truck! Join Date: Feb 2002 Location: Texas Posts: 3,775	Re: throttle cable question On mine the top part of the pedal's rod was worn out. I ended up engineering mine on with a new hole drilled out and used the kit it came with. But then I ran into an issue and used a clamp from Home Depot in the hardware section that tightens up aircraft cable. This kept it stronger than the little ball that it had came with. But if you can take your old one out and replace the same way it went. __________________ 1979 Chevrolet Bonanza Big10 "Tootsie Roll" 1985 Chevrolet Silverado (wife's) Member of the Southern Bowties Club "Don't underestimate how sexy a fat man who drinks to excess can be." Homer Simpson

05-11-2006, 08:37 PM	#3
speed Junior Member Join Date: Jan 2006 Location: Northern Iowa Posts: 258	Re: throttle cable question I worked on it some today. cut the "cup" off an old throttle cable and slid it on the cable. Didn't use the end that was sent with the cable. Now to trim it to fit nicely. __________________ Jeff J ---------- 86 El Camino 81 Monte Carlo 81 Regal 04 Colorado

05-11-2006, 09:15 PM	#4
swervin ervin You get what you pay for Join Date: Dec 1999 Location: Cherryville, NC Posts: 4,798	Re: throttle cable question Speed, that's what I did also. __________________ Mike 1985 Chevy C-10

05-16-2006, 05:12 PM	#5
bigfredtn Active Member Join Date: Dec 2002 Location: West TN (Memphis area) now. East TN (my favorite place to live). Posts: 157	Re: throttle cable question Can someone post a picture of the set up? __________________ BigFredTN 70 chevy stepside 350 with some goodies inside, turbo 400. 69 Chevy long wheel base. Dad bought new in 1970 62 Chevy Impala 98 GMC Yukon 1970 Ford Mustang Fastback I know its a Ford.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.