any pics or how-to's on removing rockers? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Blizz · 05-25-2006, 03:38 PM

I need to replace my rockers but I'm not sure where all I need to cut. I've also read that thre replacement floor pans have the inner rockers built in. I've already bought some inner rockers but I'm not sure where they go or if I need them.

Jason915 · 05-25-2006, 04:06 PM

http://ebfabman.com/index.htm

Try this link ebfabman is a board member and a body fab God.

**FRENCHBLUE72** · 05-26-2006, 09:59 PM

The rockers have spot welds that need to be drilled out along the bottom lip I am not sure how the corners come off as I have not gotten that far yet... Yes the floors have the rocker backing plate built into them... I also have extra inner's...

Blizz · 05-27-2006, 04:54 PM

Thanks French. I just found out that I'm gonna have to replace the kick panels too. I've read a bunch on floors and rockers.....even pilars but not the kick pans. How the hell do those come off? Should I do the whole thing or just the bottom piece that's actually rotted out?

Scrubby · 05-28-2006, 10:58 PM

Quote:

Originally Posted by Blizz

Should I do the whole thing or just the bottom piece that's actually rotted out?

In general, you should only cut out and replace the bad portions of the panel. Repop panels don't always fit well, so only replacing the part that is needed will make the fit easier.

05-25-2006, 03:38 PM	#1
Blizz Registered User Join Date: May 2006 Location: San Antonio, Texas Posts: 372	any pics or how-to's on removing rockers? I need to replace my rockers but I'm not sure where all I need to cut. I've also read that thre replacement floor pans have the inner rockers built in. I've already bought some inner rockers but I'm not sure where they go or if I need them.

05-25-2006, 04:06 PM	#2
Jason915 Registered User Join Date: Jan 2005 Location: Colorado Springs Posts: 693	Re: any pics or how-to's on removing rockers? http://ebfabman.com/index.htm Try this link ebfabman is a board member and a body fab God. __________________ 1971 GMC K1500 SWB Fleetside, 4" skyjacker softride and, 14 Bolt FF, HD Dana 44 4.10's 1970 K5 TBI conversion lifted etc SOLD 1968 C20 camper truck SOLD “To ban guns because criminals use them is to tell the innocent and law-abiding that their rights and liberties depend not on their own conduct, but on the conduct of the guilty and the lawless.” Jeff Snyder

05-26-2006, 09:59 PM	#3
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,591	Re: any pics or how-to's on removing rockers? The rockers have spot welds that need to be drilled out along the bottom lip I am not sure how the corners come off as I have not gotten that far yet... Yes the floors have the rocker backing plate built into them... I also have extra inner's... __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

05-27-2006, 04:54 PM	#4
Blizz Registered User Join Date: May 2006 Location: San Antonio, Texas Posts: 372	Re: any pics or how-to's on removing rockers? Thanks French. I just found out that I'm gonna have to replace the kick panels too. I've read a bunch on floors and rockers.....even pilars but not the kick pans. How the hell do those come off? Should I do the whole thing or just the bottom piece that's actually rotted out?



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.