73-87 3/4 ton lower arms on a 69 1/2 ton - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jamon8 · 05-29-2006, 10:14 PM

Can I put a 73-87 3/4 ton lower control arm on my stock 1969 1/2 ton crossmember.

If so what kind of modifications will I have to do?

jamon8 · 05-30-2006, 11:04 AM

bump

Aarons72s · 05-30-2006, 11:10 AM

Are you trying to convert the half ton to 3/4 ton? If so I think yes but if it is to use a 3/4 ton arm on a 1/2 ton to convert to 3/4 ton spindles. But not for using half ton spindles. The hole for the ball joint is larger in the 3/4 ton a-arm than the 1/2 ton. i hope this helps.

jamon8 · 05-30-2006, 01:09 PM

ok I think that I am not simplifying this enough

WILL A 73-87 3/4 TON LOWER CONTROL ARM FIT ON MY 1969 1/2 TON CROSSMEMBER.

lets not get overly technical about what I am doing although I appreciate the concern. this is all I need to know

Aarons72s · 05-30-2006, 08:51 PM

Simple Answer: YES

jamon8 · 05-31-2006, 08:38 AM

thank you

after reading my message I sounded a little snouty but sometimes all a guy wants is an response to the original question.

I am putting 89 spindals on my 69 and I need to put 3/4 ton lowers on. I have read all the posts but no one mentions all the possible solutions to the problem to broaden the possibilities.

Thanks again.

Aarons72s · 05-31-2006, 12:14 PM

No problem and good luck.

05-29-2006, 10:14 PM	#1
jamon8 Registered User Join Date: Apr 2006 Location: southern Il Posts: 335	73-87 3/4 ton lower arms on a 69 1/2 ton Can I put a 73-87 3/4 ton lower control arm on my stock 1969 1/2 ton crossmember. If so what kind of modifications will I have to do?

05-30-2006, 11:04 AM	#2
jamon8 Registered User Join Date: Apr 2006 Location: southern Il Posts: 335	Re: 73-87 3/4 ton lower arms on a 69 1/2 ton bump

05-30-2006, 11:10 AM	#3
Aarons72s Registered User Join Date: Apr 2006 Location: oklahoma Posts: 10,669	Re: 73-87 3/4 ton lower arms on a 69 1/2 ton Are you trying to convert the half ton to 3/4 ton? If so I think yes but if it is to use a 3/4 ton arm on a 1/2 ton to convert to 3/4 ton spindles. But not for using half ton spindles. The hole for the ball joint is larger in the 3/4 ton a-arm than the 1/2 ton. i hope this helps. Last edited by Aarons72s; 05-30-2006 at 11:12 AM.

05-30-2006, 01:09 PM	#4
jamon8 Registered User Join Date: Apr 2006 Location: southern Il Posts: 335	Re: 73-87 3/4 ton lower arms on a 69 1/2 ton ok I think that I am not simplifying this enough WILL A 73-87 3/4 TON LOWER CONTROL ARM FIT ON MY 1969 1/2 TON CROSSMEMBER. lets not get overly technical about what I am doing although I appreciate the concern. this is all I need to know

05-30-2006, 08:51 PM	#5
Aarons72s Registered User Join Date: Apr 2006 Location: oklahoma Posts: 10,669	Re: 73-87 3/4 ton lower arms on a 69 1/2 ton Simple Answer: YES

05-31-2006, 08:38 AM	#6
jamon8 Registered User Join Date: Apr 2006 Location: southern Il Posts: 335	Re: 73-87 3/4 ton lower arms on a 69 1/2 ton thank you after reading my message I sounded a little snouty but sometimes all a guy wants is an response to the original question. I am putting 89 spindals on my 69 and I need to put 3/4 ton lowers on. I have read all the posts but no one mentions all the possible solutions to the problem to broaden the possibilities. Thanks again.

05-31-2006, 12:14 PM	#7
Aarons72s Registered User Join Date: Apr 2006 Location: oklahoma Posts: 10,669	Re: 73-87 3/4 ton lower arms on a 69 1/2 ton No problem and good luck.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.