Needing some crossmember advice - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Voodooracer · 06-07-2006, 10:06 PM

Bought a 67 Step and it is lowered, don't know how far but I am ASSuming around 5-6 in the rear. My question is what does the pinion angle need to be now. Also my stock crossmember has grooved my driveshaft. Do I need to purchase the drop crossmember or change the pinion angle. All opinions are appreciated. Also the headers are the right part # but they are touching the A arm pivot point. Any suggestions? Thanx.

Voodooracer · 06-13-2006, 08:22 AM

So, is this a dumb question or nobody wants to help? New to these trucks and was looking for some guidance.

JAMESCHURCH13 · 06-13-2006, 08:38 AM

Quote:

Originally Posted by Voodooracer

So, is this a dumb question or nobody wants to help? New to these trucks and was looking for some guidance.

I think it's a good question. I just dont know a good answer outside of groves in drive shaft ='s bad and dont pinion angles mess up the inside of your tranny with the extra strain. I say fab your cross member a little and reinforce it. You know like put a kind of c notch in it.

maybe? Peace

clif1968 · 06-13-2006, 08:54 AM

Here's some info on pinion angles, http://www.2quicknovas.com/happypinions.html

Inthuwind · 06-13-2006, 10:22 AM

Got any pics??? Would like to see your truck and some of the problem areas.

68 short step · 06-13-2006, 12:39 PM

pinion angle needs to be = to the output shaft of the tranny , but opposite.... Ie -3 and +3

Voodooracer · 06-14-2006, 08:21 AM

Thanx for the link. This will help out. Iwill post some pics of the driveshaft so maybe you can actually see what I'm talking about.

06-07-2006, 10:06 PM	#1
Voodooracer Registered User Join Date: Feb 2006 Location: Houston, Texas Posts: 32	Needing some crossmember advice Bought a 67 Step and it is lowered, don't know how far but I am ASSuming around 5-6 in the rear. My question is what does the pinion angle need to be now. Also my stock crossmember has grooved my driveshaft. Do I need to purchase the drop crossmember or change the pinion angle. All opinions are appreciated. Also the headers are the right part # but they are touching the A arm pivot point. Any suggestions? Thanx.

06-13-2006, 08:22 AM	#2
Voodooracer Registered User Join Date: Feb 2006 Location: Houston, Texas Posts: 32	Re: Needing some crossmember advice So, is this a dumb question or nobody wants to help? New to these trucks and was looking for some guidance.

06-13-2006, 08:54 AM	#4
clif1968 Junior Member Join Date: Apr 2006 Location: Eufaula, OK Posts: 103	Re: Needing some crossmember advice Here's some info on pinion angles, http://www.2quicknovas.com/happypinions.html __________________ Clif '68 C/10 LWB, 327, TH400, 12 bolt

06-13-2006, 10:22 AM	#5
Inthuwind Straight jacket required Join Date: Oct 2003 Location: OKC, OK Posts: 882	Re: Needing some crossmember advice Got any pics??? Would like to see your truck and some of the problem areas. __________________ 1968 C10 Short Stepper 350/350 A/C P/S P/B Front disc 3/5 static/ 12bolt rear 3:73 1979 Pontiac Trans Am 10th Anniversary/455/4spd 2011 H-D Street Glide - CAMMED n lowered Dad always said,"Son, if you can't be good...be good at it."

06-13-2006, 12:39 PM	#6
68 short step Senior Member Join Date: Aug 2005 Location: tulsa OK Posts: 3,070	Re: Needing some crossmember advice pinion angle needs to be = to the output shaft of the tranny , but opposite.... Ie -3 and +3

06-14-2006, 08:21 AM	#7
Voodooracer Registered User Join Date: Feb 2006 Location: Houston, Texas Posts: 32	Re: Needing some crossmember advice Thanx for the link. This will help out. Iwill post some pics of the driveshaft so maybe you can actually see what I'm talking about.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.