Side Widows will not roll up to top - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Kantosensei · 06-07-2006, 10:28 PM

My drivers and passenger side windows will not roll up completely. They are both about 1/16 to 3/16 of an inch from reaching the end caps. Is there a way to adjust or are my window regulators worn out? The rainy seaon has begun here in Japan and I am tired of riding around with a rain suit on. Any ideas are greatly appreciated.

*72CSTC5* · 06-07-2006, 11:06 PM

Regulators are worn out would be my first guess. Do you have the upper weatherstrip in place around the top?

Kantosensei · 06-07-2006, 11:19 PM

Yes, I do have weatherstriping around the top. The windows will not reach the endcaps that are mounted to the top of the vent windows.

*72CSTC5* · 06-07-2006, 11:30 PM

Take off your door trim panels and loosen all of the bolts that hold the window regulator in the truck. Roll your window all the way it will go and tighten everything again. This may or may not fix the problem. If not buy new regulators. They may be worn. Pics of the situation would help as well.

makovai · 06-08-2006, 10:07 AM

mine does the same thing, however mine is so worn out you have to push/pull on the window while rolling it to get it to go up or down. It one of the next things to fix. Luckily the regulators are fairly inexpensive.

ecameron87 · 06-08-2006, 10:23 AM

Mine had the same problem. Turns out that the bottom of the window regulator (Where the glass is glued into) would hit the door where the felts are. Bend back the sheet metal on the door where the felts connect until it clears.

71RestoRod · 06-08-2006, 09:47 PM

If the sheet metal screws holding the door panel trim are too long... that will also keep the window from raising all the way up.

13lazer · 06-16-2006, 04:00 AM

Quote:

Originally Posted by ecameron87

Mine had the same problem. Turns out that the bottom of the window regulator (Where the glass is glued into) would hit the door where the felts are. Bend back the sheet metal on the door where the felts connect until it clears.

i was gonna say that, my anti rattles were hanging on my windows after i did complete teardown, wire wheel, grease, rubbers and felt, reassemble and adjust on my blazer doors last month and it took me a few minutes to see the problem. at least its only sheet metal.

06-07-2006, 10:28 PM	#1
Kantosensei Registered User Join Date: Jun 2005 Location: Japan Posts: 87	Side Widows will not roll up to top My drivers and passenger side windows will not roll up completely. They are both about 1/16 to 3/16 of an inch from reaching the end caps. Is there a way to adjust or are my window regulators worn out? The rainy seaon has begun here in Japan and I am tired of riding around with a rain suit on. Any ideas are greatly appreciated.

06-07-2006, 11:06 PM	#2
72CSTC5 Account Suspended Join Date: Nov 2004 Location: Deer Park, Tx. Posts: 2,522	Re: Side Widows will not roll up to top Regulators are worn out would be my first guess. Do you have the upper weatherstrip in place around the top?

06-07-2006, 11:19 PM	#3
Kantosensei Registered User Join Date: Jun 2005 Location: Japan Posts: 87	Re: Side Widows will not roll up to top Yes, I do have weatherstriping around the top. The windows will not reach the endcaps that are mounted to the top of the vent windows.

06-07-2006, 11:30 PM	#4
72CSTC5 Account Suspended Join Date: Nov 2004 Location: Deer Park, Tx. Posts: 2,522	Re: Side Widows will not roll up to top Take off your door trim panels and loosen all of the bolts that hold the window regulator in the truck. Roll your window all the way it will go and tighten everything again. This may or may not fix the problem. If not buy new regulators. They may be worn. Pics of the situation would help as well.

06-08-2006, 10:07 AM	#5
makovai Senior Member Join Date: Feb 2006 Location: oregon city Posts: 335	Re: Side Widows will not roll up to top mine does the same thing, however mine is so worn out you have to push/pull on the window while rolling it to get it to go up or down. It one of the next things to fix. Luckily the regulators are fairly inexpensive. __________________ If it aint broke..............fix it till it is. www.fast77.com 1972 - 330 hp crate, 11" lift with 39x18 mickeys. 3/4 ton, cross steer, 4 wheel disc brakes 1996 Z71 w/ 35's

06-08-2006, 10:23 AM	#6
ecameron87 Registered User Join Date: Nov 2003 Location: Tucson, Arizona Posts: 44	Re: Side Widows will not roll up to top Mine had the same problem. Turns out that the bottom of the window regulator (Where the glass is glued into) would hit the door where the felts are. Bend back the sheet metal on the door where the felts connect until it clears.

06-08-2006, 09:47 PM	#7
71RestoRod Registered User Join Date: Sep 2003 Location: Evergreen, CO Posts: 492	Re: Side Widows will not roll up to top If the sheet metal screws holding the door panel trim are too long... that will also keep the window from raising all the way up. __________________ 71 Blazer / GMPP ZZ383 / MPFI / 700R4 / 4-Wheel Disk / Ground-up frame off almost completed resto-mod



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.