|
09-09-2006, 04:57 PM
|
#1 |
|
Blue 67
 Join Date: Apr 2004
Location: Western WA
Posts: 1,178
|
Where to buy these?
Hello:
These the clips in the rear hub which hold the bearing and race in place. I damaged of them when I was trying to take the hub apart for my disc conversion. I went to dealer but they told me they are discountinued. They send me to an after market part store but they didn't have it. Is junk yard my only option? My concern is, I had a heck of time to get these out therefore I am afraid even if I find one I am gona damage it again? Any ideas would be greatly appreciated.
__________________
1953 GMC 3/4 ton: current project 1967 C20: 5.3 voretc with T5 conversion, 4 wheel 8 lug disc brake 1972 Nova: my 4 door sport sedan! 5.3 voretc + T5 conversion. drivable project, FUN!! 1979 Camaro Z28: 5.3 vortec conversion with build TH350: drivable project, Fun to drive 1992 Camaro RS convertible (Z28 clone): 5.3 conversion with build T5: on going project 2005 Silverado 2500, 4x4 Duramax, original owner |
|
|
|
09-09-2006, 05:13 PM
|
#2 |
|
Registered User
Join Date: May 2005
Location: Beaverton, OR
Posts: 3,728
|
Re: Where to buy these?
Check NAPA, they often have a lot of the hard to find stuff I've needed.
|
|
|
|
|
09-09-2006, 05:15 PM
|
#3 |
|
Blue 67
Join Date: Apr 2004
Location: Western WA
Posts: 1,178
|
Re: Where to buy these?
Actually I did. They were the one who sent me to dealer.
__________________
1953 GMC 3/4 ton: current project 1967 C20: 5.3 voretc with T5 conversion, 4 wheel 8 lug disc brake 1972 Nova: my 4 door sport sedan! 5.3 voretc + T5 conversion. drivable project, FUN!! 1979 Camaro Z28: 5.3 vortec conversion with build TH350: drivable project, Fun to drive 1992 Camaro RS convertible (Z28 clone): 5.3 conversion with build T5: on going project 2005 Silverado 2500, 4x4 Duramax, original owner |
|
|
|
|
09-09-2006, 05:29 PM
|
#4 |
|
what happened to flint mi
Join Date: Oct 2005
Location: san diego
Posts: 437
|
Re: Where to buy these?
try a different napa . not all parts guys are created equal , or ask for a manager those guys know which catalog to grab . if you really get stuck shoot me a pm im in san diego
__________________
71 swb 2wd fleet frame off in progress 72 4x4 blazer daily driver 70 olds cutlass s mint condition owned by a grandma 56 gmc 2wd project waitng 97 fiance mobile |
|
|
|
|
09-09-2006, 05:36 PM
|
#5 |
|
Blue 67
Join Date: Apr 2004
Location: Western WA
Posts: 1,178
|
Re: Where to buy these?
Thanks. I'll try.
__________________
1953 GMC 3/4 ton: current project 1967 C20: 5.3 voretc with T5 conversion, 4 wheel 8 lug disc brake 1972 Nova: my 4 door sport sedan! 5.3 voretc + T5 conversion. drivable project, FUN!! 1979 Camaro Z28: 5.3 vortec conversion with build TH350: drivable project, Fun to drive 1992 Camaro RS convertible (Z28 clone): 5.3 conversion with build T5: on going project 2005 Silverado 2500, 4x4 Duramax, original owner |
|
|
|
|
09-09-2006, 05:37 PM
|
#6 |
|
Sisyphus was my mentor!
Join Date: Sep 2002
Location: Carleton Place, Ontario CANADA
Posts: 984
|
Re: Where to buy these?
Take your old snaprings to a good bearing supply shop & they'll take care of you. Look for the same thickness & diameter. They may look different (with little holes in the end for snapring pliers) buy they will work fine.
__________________
passthebuck  #5642 -TWO 1967 GMC 910's. One with L6/3-on-the tree and the other with 355 w/435hp & a 700r4. -a 2013 Honda Civic as my "sensible" car |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
