2000 Tahoe Front wheel hub replacement - The 1947 - Present Chevrolet & GMC Truck Message Board Network

84 400 · 09-26-2006, 04:25 PM

Well i know that this is a commen Prolem on 4x4's. This tahoe is a 2000 with 115k on it and there was a funny nosie comming from the front end. sounded like a bearing and since it was going in today to get the tranny flushed we figured we could have the dealer check it out. And i was right it was the front drivers side wheel hub. Now they want 582$ to replace the hu. I have done it on a jeep before so i think i would have n problem doing it on the tahoe. Any special tools i would need? A torque wrench, and a hub puler should do right?

Any tips or tricks to doing these?

84 400 · 10-02-2006, 12:13 AM

no high milage 4x4 out there with this problem?

TheLlama · 10-02-2006, 01:59 AM

No special tools... just time and beer.

84 400 · 10-03-2006, 05:42 PM

ha ha yeah. well are the calipers held on with tork drive? I don't have any so i will need to know the size to get one. Thanks

***Josh*** · 10-03-2006, 07:29 PM

Caliper brackets should be held on with 18mm head bolts. The back of the hub has 3 15mm bolts, and I forget the size of the 4x4 axle nut.
On jackstands it shouldn't take more than an hour or two to get off, hardest part is getting the 3 bolts that hold the hub one off. With air tools and a lift I can do them in around 45 minutes or less.

84 400 · 10-03-2006, 08:28 PM

Head bolts? so am i to belive they are regular or are the special? i am not up on my lingo. I was thinking about trying to lossen the 3 bolts while the truck was on the ground so i can really lay into them. i hate working on stands cause i don't truck them. I have the tools i think and i need the hub puller right?

Thanks it is my dads truck so normally don't work on it if you can't tell

**N2TRUX** · 10-03-2006, 09:29 PM

I think he means "hex" head bolts...

*bluewhitepete* · 10-03-2006, 09:39 PM

you won't need a hub puller just a big hammer and a punch, make sure not to damage the axle. When installing it clean the rust and dirt from where the old bearing was and install the bearing by using the 3 bolts on the backside. make sure you route your wiring correctly and that the hub assembly is positioned the way you took the old one out. good luck, it is pretty simple though..

84 400 · 10-04-2006, 04:53 PM

thanks N2 and blue, i thpought they were hex head. Well i ordered the parts today hopefully they are in by this saturday

09-26-2006, 04:25 PM	#1
84 400 Sb 400 club Join Date: Nov 2005 Location: NH / MA Posts: 2,746	2000 Tahoe Front wheel hub replacement Well i know that this is a commen Prolem on 4x4's. This tahoe is a 2000 with 115k on it and there was a funny nosie comming from the front end. sounded like a bearing and since it was going in today to get the tranny flushed we figured we could have the dealer check it out. And i was right it was the front drivers side wheel hub. Now they want 582$ to replace the hu. I have done it on a jeep before so i think i would have n problem doing it on the tahoe. Any special tools i would need? A torque wrench, and a hub puler should do right? Any tips or tricks to doing these? __________________ 1984 chevy c10, built 400sb,.(SOLD) 77 K10 Project / daily driver "The Grinch" http://67-72chevytrucks.com/vboard/s...d.php?t=318363 1956 Willys Wagon (327 chevy) Project (Now Buick 225) 1980 Corvette L-48 4 speed 1992 Mustang GT built 5.0 5 speed 1985 C10 LWB Sold 1982 K10 SWB plow truck Parted out 1986 D30 M1028 fire brush truck Parted out

10-02-2006, 12:13 AM	#2
84 400 Sb 400 club Join Date: Nov 2005 Location: NH / MA Posts: 2,746	Re: 2000 Tahoe Front wheel hub replacement no high milage 4x4 out there with this problem? __________________ 1984 chevy c10, built 400sb,.(SOLD) 77 K10 Project / daily driver "The Grinch" http://67-72chevytrucks.com/vboard/s...d.php?t=318363 1956 Willys Wagon (327 chevy) Project (Now Buick 225) 1980 Corvette L-48 4 speed 1992 Mustang GT built 5.0 5 speed 1985 C10 LWB Sold 1982 K10 SWB plow truck Parted out 1986 D30 M1028 fire brush truck Parted out

10-02-2006, 01:59 AM	#3
TheLlama Registered User Join Date: Sep 2006 Location: Oklahoma Posts: 15	Re: 2000 Tahoe Front wheel hub replacement No special tools... just time and beer.

10-03-2006, 05:42 PM	#4
84 400 Sb 400 club Join Date: Nov 2005 Location: NH / MA Posts: 2,746	Re: 2000 Tahoe Front wheel hub replacement ha ha yeah. well are the calipers held on with tork drive? I don't have any so i will need to know the size to get one. Thanks __________________ 1984 chevy c10, built 400sb,.(SOLD) 77 K10 Project / daily driver "The Grinch" http://67-72chevytrucks.com/vboard/s...d.php?t=318363 1956 Willys Wagon (327 chevy) Project (Now Buick 225) 1980 Corvette L-48 4 speed 1992 Mustang GT built 5.0 5 speed 1985 C10 LWB Sold 1982 K10 SWB plow truck Parted out 1986 D30 M1028 fire brush truck Parted out

10-03-2006, 07:29 PM	#5
*Josh* He's got mean nasty FANGS! Join Date: Dec 1999 Location: Rockwell, NC Posts: 6,514	Re: 2000 Tahoe Front wheel hub replacement Caliper brackets should be held on with 18mm head bolts. The back of the hub has 3 15mm bolts, and I forget the size of the 4x4 axle nut. On jackstands it shouldn't take more than an hour or two to get off, hardest part is getting the 3 bolts that hold the hub one off. With air tools and a lift I can do them in around 45 minutes or less. __________________ 2004 K2500 Burb 1999 C3500 1985 Cutlass Supreme 1969 C-10 1967 C-10 Panel josh@67-72chevytrucks.com

10-03-2006, 08:28 PM	#6
84 400 Sb 400 club Join Date: Nov 2005 Location: NH / MA Posts: 2,746	Re: 2000 Tahoe Front wheel hub replacement Head bolts? so am i to belive they are regular or are the special? i am not up on my lingo. I was thinking about trying to lossen the 3 bolts while the truck was on the ground so i can really lay into them. i hate working on stands cause i don't truck them. I have the tools i think and i need the hub puller right? Thanks it is my dads truck so normally don't work on it if you can't tell __________________ 1984 chevy c10, built 400sb,.(SOLD) 77 K10 Project / daily driver "The Grinch" http://67-72chevytrucks.com/vboard/s...d.php?t=318363 1956 Willys Wagon (327 chevy) Project (Now Buick 225) 1980 Corvette L-48 4 speed 1992 Mustang GT built 5.0 5 speed 1985 C10 LWB Sold 1982 K10 SWB plow truck Parted out 1986 D30 M1028 fire brush truck Parted out

10-03-2006, 09:29 PM	#7
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,021	Re: 2000 Tahoe Front wheel hub replacement I think he means "hex" head bolts... __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra"

10-03-2006, 09:39 PM	#8
bluewhitepete chevy72402 under a new name to get past a ban Join Date: Apr 2006 Location: SD Posts: 12	Re: 2000 Tahoe Front wheel hub replacement you won't need a hub puller just a big hammer and a punch, make sure not to damage the axle. When installing it clean the rust and dirt from where the old bearing was and install the bearing by using the 3 bolts on the backside. make sure you route your wiring correctly and that the hub assembly is positioned the way you took the old one out. good luck, it is pretty simple though..

10-04-2006, 04:53 PM	#9
84 400 Sb 400 club Join Date: Nov 2005 Location: NH / MA Posts: 2,746	Re: 2000 Tahoe Front wheel hub replacement thanks N2 and blue, i thpought they were hex head. Well i ordered the parts today hopefully they are in by this saturday __________________ 1984 chevy c10, built 400sb,.(SOLD) 77 K10 Project / daily driver "The Grinch" http://67-72chevytrucks.com/vboard/s...d.php?t=318363 1956 Willys Wagon (327 chevy) Project (Now Buick 225) 1980 Corvette L-48 4 speed 1992 Mustang GT built 5.0 5 speed 1985 C10 LWB Sold 1982 K10 SWB plow truck Parted out 1986 D30 M1028 fire brush truck Parted out



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.