Damper pulley question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

*wolfthing2000* · 10-23-2006, 10:04 PM

I just removed the alternator and related stuff from the front of a 350 that I am pulling out of a 69 4x4. Non of the engine is original, it is the 3rd engine in the truck ( the PO thought)!! I was going to use the pulleys and brackets, power steering etc. on my new 383 going back in. After removing the alternator I was able to lign of sight the power steering pump pulley to the damper pulley front groove. The damper pulley is 3/8 of an inch to the rear from the power steering pump pulley. It worked that way and everything seems tight. What is up here???? It is the short water pump by the way.
Thanks

*wolfthing2000* · 10-24-2006, 08:51 AM

ttt

JimKshortstep4x4 · 10-24-2006, 09:53 AM

You probably have a mixture of pullies and brackets. The 69 originally had a cast pully and cast power steering pump brackets. If either is stamped then they will not align.

Jim

*wolfthing2000* · 10-24-2006, 02:21 PM

So will the stuff off a 400 work?? I believe the alternator was on the other side is the only diff that I seem to remember

JimKshortstep4x4 · 10-24-2006, 07:39 PM

The 400 parts will fit, but it probably has the long water pump so everything will be different.

Jim

**uncle** · 10-24-2006, 08:31 PM

If it's only 3/8" off, you'll probably be ok. I've seen some from the factory off that much.

*wolfthing2000* · 10-24-2006, 10:22 PM

Yea, the PO ran it that way for who knows how long and I ran it for another 1000miles or so before I decided to start the project. Anyway, I am going to start looking for options. If I buy a set of pulleys from Summit or Jegs, will they match up okay???? Or is it a matter of moving the power steering pump, or perhaps an offset pulley on the pump????

10-23-2006, 10:04 PM	#1
wolfthing2000 Account Suspended Join Date: Oct 2004 Posts: 1,276	Damper pulley question I just removed the alternator and related stuff from the front of a 350 that I am pulling out of a 69 4x4. Non of the engine is original, it is the 3rd engine in the truck ( the PO thought)!! I was going to use the pulleys and brackets, power steering etc. on my new 383 going back in. After removing the alternator I was able to lign of sight the power steering pump pulley to the damper pulley front groove. The damper pulley is 3/8 of an inch to the rear from the power steering pump pulley. It worked that way and everything seems tight. What is up here???? It is the short water pump by the way. Thanks

10-24-2006, 08:51 AM	#2
wolfthing2000 Account Suspended Join Date: Oct 2004 Posts: 1,276	Re: Damper pulley question ttt

10-24-2006, 09:53 AM	#3
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	Re: Damper pulley question You probably have a mixture of pullies and brackets. The 69 originally had a cast pully and cast power steering pump brackets. If either is stamped then they will not align. Jim

10-24-2006, 02:21 PM	#4
wolfthing2000 Account Suspended Join Date: Oct 2004 Posts: 1,276	Re: Damper pulley question So will the stuff off a 400 work?? I believe the alternator was on the other side is the only diff that I seem to remember

10-24-2006, 07:39 PM	#5
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	Re: Damper pulley question The 400 parts will fit, but it probably has the long water pump so everything will be different. Jim

10-24-2006, 08:31 PM	#6
uncle Senior Member Join Date: Aug 2003 Location: Conyers,Ga. Posts: 7,288	Re: Damper pulley question If it's only 3/8" off, you'll probably be ok. I've seen some from the factory off that much.

10-24-2006, 10:22 PM	#7
wolfthing2000 Account Suspended Join Date: Oct 2004 Posts: 1,276	Re: Damper pulley question Yea, the PO ran it that way for who knows how long and I ran it for another 1000miles or so before I decided to start the project. Anyway, I am going to start looking for options. If I buy a set of pulleys from Summit or Jegs, will they match up okay???? Or is it a matter of moving the power steering pump, or perhaps an offset pulley on the pump????



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.