What did you get done? 10/29 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**N2TRUX** · 10-29-2006, 08:42 PM

I didn't do anything to my 77 Cheyenne this week. I'm planning on pulling it out next week and go for a cruise if the weather stays this nice.

Saturday I washed all my daily drivers since it rained this week. My wife's Denali got a complete detail and my Silverado got a wash and dry. I spent the afternoon finishing up my lighting project on my house. After 3 more trips to the hardware store I finally have all the fixtures matching.

I made a few service calls this morning then I found some time to work on my Silverado CC. I finally located some stainless carriage bolts to put in the license plate holes on the front bumper. I chucked them up in my drill, filed the heads down low, and polished them up so they shine like chrome.

I put them in the bumper and polished the marks where the front plate was mounted. That lead to polishing the bumper which lead to a complete wax and detail of the entire truck....

What did you get done?

82c10 · 10-29-2006, 09:51 PM

i worked all day saturday, when we were about to leave for lunch a mexican cement guy came and asked us if we had jumper cables, we were like no, because we didn't have any, as we was about to leave my dad remembered we had some romex in the bed, we had 2 strands like 3 1/2 feet long, i pulled the truck up to where it was touching plastic to plastic, and hooked them up, needless to say ROMEX CAN ACT AS JUMPER CABLES!

pcmcobra · 10-29-2006, 10:00 PM

Started by deciding to lower my tweeters by 3db on the crossovers. It's done by a jumper. I mounted the crossovers way up in the dash, anyways, as I was trying to see (my son killed the batteries in every single flashlight I own!), I dropped the tiny jumper, ARGHHHH, fell behind the kick panel, into where the rubber vent is...I never found it, luckily I have another complete set of components, and stole a jumper, but I want my jumper back!!!!!!
Got that done, cleaned up some junk in the garage, now my truck bed is full, guess I'll make a dump run next weekend.
Been so busy at work, I cut the grass and edged for the last time this year, until spring...

cliffsta · 10-29-2006, 10:06 PM

Well, my A/C died on Thursday, and I have neither the time, knowledge, or money to get it fixed. Saturday I got a speeding ticket, 63 in a 45 (darn speed trap) so instead of going to Nachitoches for the football game I came back to the house and continued stripping the 1984's interior.

I took out the carpet, insulation, and rubber pad, sooooo gross.

Also removed the jank cardboard panel and storage bag thingie, and all the plastic/metal trim in the cab. The only interior left in the truck is the headliner. And MAN OH MAN is the floor beautiful on that truck! Only rot that is starting is, ironically, underneath the rubber seals. Next weekend I'm going to remove the gauge cluster with the assistance of my dad. During the week this coming week I plan on removing the hood and fenders to clean them up, picture them, and list them for sale.

Also starting to get a bit of valve clatter in Ol' Red, but that may be related to some bad gas. *crosses fingers* Poor ol' truck. Carburetor is SHOT. No doubt a camlobe is rounded off. Just one more winter....

Rather eventful truck(s) weekend if I do say so.

Jonboy · 10-29-2006, 10:08 PM

I went to go check out new mobile homes for a buddy of mine's new lake lot. We went to the manufacturing plant, and it was actually pretty cool. That was most of Saturday.

Friday night, we went to see Jimmie Vaughan play at the Lakewood Theater (a restored twenties theater in Dallas). We were able to go right up to the stage. It was a fundraiser, so there were not a wole lot of people there, maybe 300 or so. It was a great concert, in a really cool venue.

Today, I purchased a new chainsaw, and cleared a ton of trees at my mother in law's house. Everything was going fine, until I got hit in the mouth with a big branch. At least that got me a good, homecooked meal!

bcj67chevy · 10-29-2006, 10:17 PM

celebrated my 22nd birthday

mySAVIOReigns · 10-29-2006, 10:47 PM

Went to the swap meet and got an exhaust tip from a friend for a buck, can't beat that.

Then didn't do anything else.

**N2TRUX** · 10-29-2006, 10:55 PM

Today I had the joy of cleaning flower bed and trimming trees but it was not a total loss. I loaded up all the branches and trash in the back of the 68 and headed to our shop dumpster, my son said I was crazy for using it but that's what I built it for and besides the dogs get to ride and they are starting to really like the lowered truck.

(Ken, it looks like you used my Netscape the last time you vistied : ) what's funny is that I logged in ? ) N2billet-Keith

bagged74 · 10-30-2006, 12:15 AM

I got my new daily driver on the road.

I got a smoking deal on a 96 s10 blazer a couple of weeks ago. only problem was it needed an engine. found one and a guy to cahnge it for cheap... so im on the road with a new beater/driver.

I also got a lowering kit and some wheels rounded up for it....pics to come later

I also carved a few pumpkins with the kiddos tonight..

84 400 · 10-30-2006, 12:35 AM

well the weather here was crazy so i was stuck in the gardge. i did get to replace the govner gear in my 62 wheel horse and took some pics. i got to go get the rad flushed in my 84 then it is staybil time and cover up for a long winter. Also took some pics of my seat and the wheel horse. My seat is gonna need some help soon it is killing my back! also played with the new digi camera and took some pics of the seat. and the 62 for those who pm'ed me about her. i got the back half in new paint and am going to have to wait for warmer weather for the front

rfmaster · 10-30-2006, 10:00 AM

Pulled a complete TBI harness and system from B-Body donor car at the local junk yeard. Did some research into surge tanks, since 75 does not have buffles in the gas tanks. Lots internet research into Carb to TBI conversion....

RFmaster

Bad Karma · 10-30-2006, 10:06 AM

Rebuilt and rejetted my quadrajet so I can get through emissions testing next weekend... Found out my power valve was stuck in the "up" position, which explains the test failure from before. Sure runs good now.

redz 1970 K5 · 10-30-2006, 11:21 AM

Saturday, washed the burb... Even in cooler weather, the thing is SO huge, by the time I get to drying it, I have waterspots on the windshield. Thing looks great. I am 100% convinced that the Bilsteins I installed on my burb last week are the best shocks I have ever had. I thought they were a little stiff at first, but after about 100 miles or so, they ride just AMAZING now. That truck's street manners are just incredible now. I went from something that feels spongy and vague to the complete opposite.

Took the dirtbike to the track Sunday... What a great day. Last weekend the track is open though...

SCOTI · 10-30-2006, 01:19 PM

Sat I spent a little time @ work & then went & looked @ a 67 short-step. We went to go see Saw III because my GF's daughter just had to see it..... yet they all sat through the movie w/their hands covering their eyes

.

Sun I actually got my engine hoist & misc tools back from my friend. I went ahead & spent the day getting my SBC dropped into my 68 only to pull it back out to correct some issues. Oh well maybe next weekend.....

Oh, I managed to scratch my freshly painted firewall in 2 spots getting the motor out! That sucks.

Hoods69BadBowTie · 10-30-2006, 03:18 PM

I got some work done on my Cavy on Sunday. Got a whole new bumper painted and on. New turnsignals, simdemarker lights and headlights. Hung out with my dad and my bros on Saturday. Just chilled and watched some movies on Friday.
-Peace

Billy81 · 10-30-2006, 04:12 PM

I changed the fuel pump on my 86 blazer and cleaned the interior a bit.

pcmcobra · 10-30-2006, 06:46 PM

had to work today, it's been a crazy month...busy.
Found a guy locally who has a 5.3/4l60 for sale. Came out of an 04 tahoe w/ 9k miles!
He is asking $2k, would probably take less, he's desperate to get rid of it to buy a 6.0l
what a steal, too bad my wallet is on permanent vacation or I would take the plunge.
I did score a 91 burb fgrill/support and all accessories for a swap for $150....The grill is in good shape, has one bad spot.
Not a bad deal at all. Been waiting for one of these. Maybe I'll do it over a few vacation days or comp days from work over xmas.
Will post pics.

1985K10 · 10-30-2006, 07:50 PM

Im finally getting my 87 Sierra back together...put on the front fenders and innder fenders, grille and all the trim, tail lights...Gonna sell the blazer soon i think so i need to get this truck done!

10-29-2006, 08:42 PM	#1
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,023	What did you get done? 10/29 I didn't do anything to my 77 Cheyenne this week. I'm planning on pulling it out next week and go for a cruise if the weather stays this nice. Saturday I washed all my daily drivers since it rained this week. My wife's Denali got a complete detail and my Silverado got a wash and dry. I spent the afternoon finishing up my lighting project on my house. After 3 more trips to the hardware store I finally have all the fixtures matching. I made a few service calls this morning then I found some time to work on my Silverado CC. I finally located some stainless carriage bolts to put in the license plate holes on the front bumper. I chucked them up in my drill, filed the heads down low, and polished them up so they shine like chrome. I put them in the bumper and polished the marks where the front plate was mounted. That lead to polishing the bumper which lead to a complete wax and detail of the entire truck.... What did you get done? __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra"

10-29-2006, 09:51 PM	#2
82c10 needin' money Join Date: May 2005 Location: Chickasha, Oklahoma Posts: 1,106	Re: What did you get done? 10/29 i worked all day saturday, when we were about to leave for lunch a mexican cement guy came and asked us if we had jumper cables, we were like no, because we didn't have any, as we was about to leave my dad remembered we had some romex in the bed, we had 2 strands like 3 1/2 feet long, i pulled the truck up to where it was touching plastic to plastic, and hooked them up, needless to say ROMEX CAN ACT AS JUMPER CABLES! __________________ *SWB Stands for Short Wide Bed*

10-29-2006, 10:00 PM	#3
pcmcobra Registered User Join Date: Aug 2006 Location: Florida Posts: 1,684	Re: What did you get done? 10/29 Started by deciding to lower my tweeters by 3db on the crossovers. It's done by a jumper. I mounted the crossovers way up in the dash, anyways, as I was trying to see (my son killed the batteries in every single flashlight I own!), I dropped the tiny jumper, ARGHHHH, fell behind the kick panel, into where the rubber vent is...I never found it, luckily I have another complete set of components, and stole a jumper, but I want my jumper back!!!!!! Got that done, cleaned up some junk in the garage, now my truck bed is full, guess I'll make a dump run next weekend. Been so busy at work, I cut the grass and edged for the last time this year, until spring...

10-29-2006, 10:06 PM	#4
cliffsta Stepsides RULE Join Date: Jul 2004 Location: Pineville, LA Posts: 1,921	Re: What did you get done? 10/29 Well, my A/C died on Thursday, and I have neither the time, knowledge, or money to get it fixed. Saturday I got a speeding ticket, 63 in a 45 (darn speed trap) so instead of going to Nachitoches for the football game I came back to the house and continued stripping the 1984's interior. I took out the carpet, insulation, and rubber pad, sooooo gross. Also removed the jank cardboard panel and storage bag thingie, and all the plastic/metal trim in the cab. The only interior left in the truck is the headliner. And MAN OH MAN is the floor beautiful on that truck! Only rot that is starting is, ironically, underneath the rubber seals. Next weekend I'm going to remove the gauge cluster with the assistance of my dad. During the week this coming week I plan on removing the hood and fenders to clean them up, picture them, and list them for sale. Also starting to get a bit of valve clatter in Ol' Red, but that may be related to some bad gas. crosses fingers Poor ol' truck. Carburetor is SHOT. No doubt a camlobe is rounded off. Just one more winter.... Rather eventful truck(s) weekend if I do say so. __________________ 1981 Chevy C10 Custom Deluxe Stepside 350 V8, headers, side exhausts, 3-speed auto SOLD 1980 Chevy C10 Custum Deluxe Stepside 305 V8, Edelbrock Performer Intake, Edelbrock 1406 600CFM 4-barrel, TH350C. Bent rod. SOLD 1984 GMC Sierra Classic Longbed 6.2L Diesel SOLD 2009 Kawasaki KLX-250S too many mods for this signature 1999 Honda Accord EX 4-cylinder, 17" Motegi Wheels 215/45/17 Sumitomo tires, Tein S-Tech lowering springs, KYB GR2 shocks, Acura TL 20mm rear swaybar, debadged, blackhoused headlights, Short-Ram Intake Cardomain of the Accord Last edited by cliffsta; 10-29-2006 at 10:09 PM.

10-29-2006, 10:08 PM	#5
Jonboy Slots go on anything! Join Date: May 2003 Location: Richardson, TX Posts: 5,957	Re: What did you get done? 10/29 I went to go check out new mobile homes for a buddy of mine's new lake lot. We went to the manufacturing plant, and it was actually pretty cool. That was most of Saturday. Friday night, we went to see Jimmie Vaughan play at the Lakewood Theater (a restored twenties theater in Dallas). We were able to go right up to the stage. It was a fundraiser, so there were not a wole lot of people there, maybe 300 or so. It was a great concert, in a really cool venue. Today, I purchased a new chainsaw, and cleared a ton of trees at my mother in law's house. Everything was going fine, until I got hit in the mouth with a big branch. At least that got me a good, homecooked meal!

10-29-2006, 10:17 PM	#6
bcj67chevy 402 BIG BLOCK Join Date: Mar 2006 Location: McClelland IA Posts: 286	Re: What did you get done? 10/29 celebrated my 22nd birthday

10-29-2006, 10:47 PM	#7
mySAVIOReigns Active Member Join Date: Mar 2006 Location: Arlington, TX Posts: 111	Re: What did you get done? 10/29 Went to the swap meet and got an exhaust tip from a friend for a buck, can't beat that. Then didn't do anything else. __________________ Website Here -Stephen 1985 Chevy Silverado, 1/2 ton

10-29-2006, 10:55 PM	#8
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,023	Re: What did you get done? 10/29 Today I had the joy of cleaning flower bed and trimming trees but it was not a total loss. I loaded up all the branches and trash in the back of the 68 and headed to our shop dumpster, my son said I was crazy for using it but that's what I built it for and besides the dogs get to ride and they are starting to really like the lowered truck. (Ken, it looks like you used my Netscape the last time you vistied : ) what's funny is that I logged in ? ) N2billet-Keith Attached Images __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra" Last edited by N2TRUX; 10-29-2006 at 10:57 PM.

10-30-2006, 12:15 AM	#9
bagged74 its just $$$$$ Join Date: Jul 2003 Location: OK Posts: 2,078	Re: What did you get done? 10/29 I got my new daily driver on the road. I got a smoking deal on a 96 s10 blazer a couple of weeks ago. only problem was it needed an engine. found one and a guy to cahnge it for cheap... so im on the road with a new beater/driver. I also got a lowering kit and some wheels rounded up for it....pics to come later I also carved a few pumpkins with the kiddos tonight.. Last edited by bagged74; 10-30-2006 at 12:15 AM.

10-30-2006, 12:35 AM	#10
84 400 Sb 400 club Join Date: Nov 2005 Location: NH / MA Posts: 2,743	Re: What did you get done? 10/29 well the weather here was crazy so i was stuck in the gardge. i did get to replace the govner gear in my 62 wheel horse and took some pics. i got to go get the rad flushed in my 84 then it is staybil time and cover up for a long winter. Also took some pics of my seat and the wheel horse. My seat is gonna need some help soon it is killing my back! also played with the new digi camera and took some pics of the seat. and the 62 for those who pm'ed me about her. i got the back half in new paint and am going to have to wait for warmer weather for the front Attached Images __________________ 1984 chevy c10, built 400sb,.(SOLD) 77 K10 Project / daily driver "The Grinch" http://67-72chevytrucks.com/vboard/s...d.php?t=318363 1956 Willys Wagon (327 chevy) Project (Now Buick 225) 1980 Corvette L-48 4 speed 1992 Mustang GT built 5.0 5 speed 1985 C10 LWB Sold 1982 K10 SWB plow truck Parted out 1986 D30 M1028 fire brush truck Parted out

10-30-2006, 10:00 AM	#11
rfmaster Registered User Join Date: Oct 2003 Location: OC CA Posts: 1,374	Re: What did you get done? 10/29 Pulled a complete TBI harness and system from B-Body donor car at the local junk yeard. Did some research into surge tanks, since 75 does not have buffles in the gas tanks. Lots internet research into Carb to TBI conversion.... RFmaster __________________ "The Beast" 1975 Chevrolet C20 longbed 350/700R4! with 3inch body lift Dual Flowmasters Super 40's! TBI retrofit completed (2007-07-29) New 383CID (+030) 08-304-8 9.5:1CR x36,005 (2012-12-17)

10-30-2006, 10:06 AM	#12
Bad Karma Magnificent bastard Join Date: Oct 2004 Location: Glendale, AZ Posts: 196	Re: What did you get done? 10/29 Rebuilt and rejetted my quadrajet so I can get through emissions testing next weekend... Found out my power valve was stuck in the "up" position, which explains the test failure from before. Sure runs good now. __________________ 1977 Big Block Burb

10-30-2006, 11:21 AM	#13
redz 1970 K5 OBS guy Join Date: Jun 2004 Location: SoCal Posts: 1,060	Re: What did you get done? 10/29 Saturday, washed the burb... Even in cooler weather, the thing is SO huge, by the time I get to drying it, I have waterspots on the windshield. Thing looks great. I am 100% convinced that the Bilsteins I installed on my burb last week are the best shocks I have ever had. I thought they were a little stiff at first, but after about 100 miles or so, they ride just AMAZING now. That truck's street manners are just incredible now. I went from something that feels spongy and vague to the complete opposite. Took the dirtbike to the track Sunday... What a great day. Last weekend the track is open though... __________________ 88 Suburban Goodies- Alpine, Auto Meter, BDS, Bilstein, B&M, BFG, Borgeson, Bushwhacker, Cowl hood, Flowmaster, Genuine Gear, Holley, Infinity, JVC, K&N, MB Wheels, MSD, Pioneer, Skyjacker, Sony, Thorley, Walker + more

10-30-2006, 01:19 PM	#14
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 21,964	Re: What did you get done? 10/29 Sat I spent a little time @ work & then went & looked @ a 67 short-step. We went to go see Saw III because my GF's daughter just had to see it..... yet they all sat through the movie w/their hands covering their eyes . Sun I actually got my engine hoist & misc tools back from my friend. I went ahead & spent the day getting my SBC dropped into my 68 only to pull it back out to correct some issues. Oh well maybe next weekend..... Oh, I managed to scratch my freshly painted firewall in 2 spots getting the motor out! That sucks. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

10-30-2006, 03:18 PM	#15
Hoods69BadBowTie Chevys Kick A$$ Join Date: Jan 2005 Location: Zootown, MT Posts: 12,699	Re: What did you get done? 10/29 I got some work done on my Cavy on Sunday. Got a whole new bumper painted and on. New turnsignals, simdemarker lights and headlights. Hung out with my dad and my bros on Saturday. Just chilled and watched some movies on Friday. -Peace __________________ HOODS is what I answer too -'79, '77, '88 Pickup Sold, '85 Camaro, '83 T/A, '81,'83,'90 K5 Blazer All Sold -'79 3/4 ton "Big Yellow Bananna" Lifted 4spd. 39.5 TSL Swampers, The money Pit -'86 K5 Blazer Silverado 6.2 4" lift 35"s -'95 Ext. Cab Shorty 4" Tuff Country rolling 35" M/T's -'83 Monte Carlo T-Tops. 126,500 Original Miles -LATER I would rather push a Chevy then drive a ford!!



Register or Log In To remove these advertisements.

10-30-2006, 04:12 PM	#16
Billy81 Registered User Join Date: Jun 2004 Location: Medford,Oregon Posts: 390	Re: What did you get done? 10/29 I changed the fuel pump on my 86 blazer and cleaned the interior a bit.

10-30-2006, 06:46 PM	#17
pcmcobra Registered User Join Date: Aug 2006 Location: Florida Posts: 1,684	Re: What did you get done? 10/29 had to work today, it's been a crazy month...busy. Found a guy locally who has a 5.3/4l60 for sale. Came out of an 04 tahoe w/ 9k miles! He is asking $2k, would probably take less, he's desperate to get rid of it to buy a 6.0l what a steal, too bad my wallet is on permanent vacation or I would take the plunge. I did score a 91 burb fgrill/support and all accessories for a swap for $150....The grill is in good shape, has one bad spot. Not a bad deal at all. Been waiting for one of these. Maybe I'll do it over a few vacation days or comp days from work over xmas. Will post pics. Last edited by pcmcobra; 10-30-2006 at 07:05 PM.

10-30-2006, 07:50 PM	#18
1985K10 Registered User Join Date: Oct 2003 Location: CT Posts: 315	Re: What did you get done? 10/29 Im finally getting my 87 Sierra back together...put on the front fenders and innder fenders, grille and all the trim, tail lights...Gonna sell the blazer soon i think so i need to get this truck done! __________________ Anthony 07 Tahoe LT 70 Chevelle 450HP 383-TH400 77 GMC Royal Sierra~Resto in progress~

Register or Log In To remove these advertisements.